Werbung
OBJ_BUCH-310-006.book Page 19 Monday, March 26, 2012 2:15 PM
Angle Grinder
Thread of grinder spindle
Thread length (max.) of grinder spindle
Reduced starting current
Constant electronic control
Weight according to EPTA-Procedure
01/2003
Protection class
The values given are valid for a nominal voltage [U] of 230 V. For different voltages and models for specific countries, these values can vary.
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under "Technical Data" is in conformity with the fol-
lowing standards or standardization documents: EN 60745
according to the provisions of the directives 2011/65/EU,
2004/108/EC, 2006/42/EC.
Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ETM9,
D-70745 Leinfelden-Echterdingen
Dr. Egbert Schneider
Helmut Heinzelmann
Senior Vice President
Head of Product Certification
Engineering
PT/ETM9
Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
12.03.2012
Assembly
Mounting the Protective Devices
Before any work on the machine itself, pull the mains
plug.
Note: After breakage of the grinding disc during operation or
damage to the holding fixtures on the protection guard/power
tool, the machine must promptly be sent to an after-sales
service agent for maintenance for addresses, see section "Af-
ter-sales Service and Customer Assistance".
Protection Guard for Grinding
Place the protection guard 11 on-
to the spindle collar as shown in
the illustration. The triangle marks
on the protection guard must cor-
respond with the respective
marks on the gear case.
Press the protection guard 11 on-
to the spindle collar until the
shoulder of the protection guard
is seated against the flange of the
machine, and turn the protection
guard until it can clearly be heard
to engage.
Bosch Power Tools
GWS 1000
GWS 1000
M 14
mm
22
–
–
kg
2.1
/II
Adjust the position of the protection guard 11 to the require-
ments of the work process. For this, press the release lever 1
upward and turn the protection guard 11 to the required po-
sition.
Adjust the protection guard 11 in such a manner that
sparking is prevented in the direction of the operator.
The protection guard 11 may be turned only upon actu-
ation of the release lever 1! Otherwise the power tool
may not continue to be used under any circumstances
and must be taken to an after-sales service agent.
Note: The encoding keys on the protection guard 11 ensure
that only a protection guard that fits the machine type can be
mounted.
Protection Guard for Cutting
For cutting with bonded abrasives, always use the pro-
tection guard for cutting 13.
Provide for sufficient dust extraction when cutting
stone.
The protection guard for cutting 13 is mounted in the same
manner as the protection guard for grinding 11.
Cutting Guide with Dust Extraction Protection Guard
The cutting guide with dust extraction protection guard 20 is
mounted in the same manner as the protection guard for
grinding 11.
Extraction Hood for Sanding
The extraction hood 6 can be used for low-dust sanding of
paint, varnish and plastics in conjunction with the carbide
grinding head 8 or the rubber sanding plate 16 with a sanding
sheet 17. The extraction hood 6 is not suitable for working
metals.
A suitable Bosch vacuum cleaner can be connected to the ex-
traction hood 6.
The extraction hood 6 is mounted in the same manner as the
protection guard 11. The brush collar is exchangeable.
Auxiliary Handle
Operate your machine only with the auxiliary handle 4.
Screw the auxiliary handle 4 on the right or left of the machine
head depending on the working method.
Hand Guard
For operations with the rubber sanding plate 16 or with
the cup brush/wheel brush/flap disc, always mount the
hand guard 15.
The hand guard 15 is fastened with the auxiliary handle 4.
English | 19
GWS 1100
GWS 1400
M 14
M 14
22
22
–
–
2.1
2.0
/II
/II
1 609 929 Y16 | (26.3.12)
M 14
22
2.2
/II
Werbung
