Battery Charge Indicator; Changing The Tool; Method Of Operation; Starting Operation - Bosch GDR Professional 18V-200 Originalbetriebsanleitung

Battery charge indicator

The green LEDs on the battery charge indicator indicate the
state of charge of the battery. For safety reasons, it is only
possible to check the state of charge when the power tool is
not in operation.
Press the button for the battery charge indicator or
show the state of charge. This is also possible when the bat-
tery is removed.
If no LED lights up after pressing the button for the battery
charge indicator, then the battery is defective and must be
replaced.
Battery model GBA 18V...
LEDs
3× continuous green light
2× continuous green light
1× continuous green light
1× flashing green light
Battery model ProCORE18V...
LEDs
5× continuous green light
4× continuous green light
3× continuous green light
2× continuous green light
1× continuous green light
1× flashing green light

Changing the Tool

Remove the battery from the power tool before carry-
u
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
Regularly clean the power tool's air vents. The motor's
u
fan can draw the dust inside the housing and excessive
accumulation of powdered metal may cause electrical
hazards.
Use application tool: GDR/GDX 18V-200 (see figure A –
B)
Pull the locking sleeve (2) forward, guide the application tool
(1) into the tool holder as far as it will go and release the
locking sleeve (2) to lock the application tool.
Impact-proof screwdriver bits (12) can be inserted using a
universal bit holder with ball catch (11).
Impact-proof screwdriver bits (12) can be inserted using a
universal bit holder with ball catch (11).
Bosch Power Tools
Use application tool: GDX/GDS 18V-200 (see figure B –
C)
When working with an application tool, pay attention
u
that the application tool is connected securely to the
tool holder. When the application tool is not securely
connected with the tool holder, it can come off during ap-
to
plication.
Slide the application tool (13) onto the square drive of the
tool holder (1).
Due to the way the system operates, the application tool
(13) will move around slightly in the tool holder (1); this has
no influence on the function/safety.
Some application tools (e.g. double bits) cannot be safely
secured in the tool holder.
Removing
Pull the locking sleeve (2) forward and remove the applica-
Capacity
tion tool.
60−100 %
30−60 %
Operation
5−30 %

Method of Operation

0−5 %
The tool holder (1) (with the application tool) is driven by an
electric motor via a gear and impact mechanism.
The working procedure is divided into two phases:
Screwing in and tightening (impact mechanism in action).
The impact mechanism is activated as soon as the screwed
connection runs tight and load is therefore put on the motor.
Capacity
The impact mechanism then converts the power of the mo-
80−100 %
tor to steady rotary impacts. When loosening screws or nuts,
60−80 %
the process is reversed.
40−60 %

Starting Operation

20−40 %
Inserting the Battery
5−20 %
Use only original Bosch lithium-ion batteries with the
u
0−5 %
voltage stated on the type plate of your power tool.
Using other batteries can lead to injuries and pose a fire
hazard.
Set the rotational direction switch (7) to the middle position
to avoid unintentionally switching it on. Insert the charged
battery (4) into the handle until you feel it engage and it is
flush with the handle.
Set the rotational direction (see figure D)
The rotational direction switch (7) is used to change the ro-
tational direction of the power tool. However, this is not pos-
sible while the on/off switch (8) is being pressed.
Right rotation: To drive in screws and tighten nuts, press
the rotational direction switch (7) through to the left stop.
Left Rotation: To loosen and unscrew screws and nuts,
press the rotational direction switch (7) through to the right
stop.
Switching on/off
To start the power tool, press and hold the on/off switch
(8).
English | 15
1 609 92A 53Z | (27.09.2019)