Warnings For The Installer - Tekno Point ATHENA R32 A-0732 Installationsanleitungen

Do not insert fingers or objects into the air inlet or outlet to avoid injury or damage the units.
Do not block the air outlet or air inlet to the units in order not to generate malfunction or damage to them.
Never add water or soak in remote as it may damage.
If the following phenomena occur, it is necessary to turn off the air conditioner, immediately disconnect the power
supply and then immediately contact the installer:
• The power cord is overheated or damaged;
• Abnormal noises are detected during operation;
• There is a frequent intervention of the protection systems of the electrical system;
• The air conditioner produces a burning smell;
• The unit has a refrigerant gas leak.
If the air conditioner is operated in abnormal conditions, it can be damaged, malfunction, generate electric shock
or fire.
Operate the emergency start button on the indoor unit (where present) only with an electrically isolated object and
not on metal as it could cause electric shock.
Do not climb on or place heavy objects on the unit as the unit may break, damage or malfunction.

1.4 Warnings for the installer

The installation must be carried out exclusively by qualified professionals in order not to damage or generate mal-
function of the units or of the entire system.
During installation it is necessary to follow all the safety rules to electrical installations and to plants with gas.
need to follow the local safety standards and to provide for appropriate protection systems on power circuits
electric.
A magnetothermic switch of suitable size must be provided in order to protect the system from possible overloads
and short circuits.
At least one isolating switch of adequate size must be provided which sections each single phase and any neutral
cable. Or a removable and easily accessible power plug at the end of the installation.
The system must be connected securely to an adequate earthing system as the failure to connect could cause
shocks, electric shocks or generate malfunctions to the units.
Install adequate section power cables before using the system.
Use only certified power and communication cables.
Make sure that the power supply matches the requirements of the system to be installed. A power supply of fre-
quency and / or voltage different from the one foreseen or of unstable values, or incorrect wiring will cause malfun-
ctions to the system or damage to the units.
Connect to a system power supply terminal is the / the cable / s phase, that the eventual neutral cable that the
earthing cable.
Make sure always to have interrupted the power supply before carrying out any work related to electrical con-
nections and, in any event, follow always all the relevant safety procedures.
Do not power the system before the installation is complete.
If the power cord or communications cable is damaged no need to be replaced by qualified personnel.
Keep distance or use special insulation between the power cables and the communication and the piping of gas
because the high temperatures of the pipes could damage the cables.
The system must be installed following the current regulations relating to electrical systems and systems with
fluorinated gases.
The installation must be carried out in compliance with the requirements of IEC, NEC and CEC or equivalent and
exclusively by qualified personnel.
The air conditioner is the first class electrical equipment. It must be properly grounded with a dedicated grounding
device. The earthing system must have been built by professionals in compliance with current regulations.
During installation, make sure that an earthing system exists and that the units are connected to earth efficiently
as electric shocks or electric shocks or malfunctions could occur.
The yellow-green cable identifies the grounding cable and must never be used for other purposes.
The earthing resistance must comply with current national electrical safety regulations.
The switch or the power plug of the unit must always be easy to log in by users at the conclusion.
All power and communication cables must be installed by qualified person. If the power cable is of insufficient
length, replace it with one of adequate length. Do not ever joints more cables.
In installations that do not include the power plug, a disconnector installed on the line and a must be provided.
Moving the air conditioner from one place to another must only be carried out by qualified personnel in order not
to incur physical injury or damage the units.
Provide always places the installation of the units outside of the reach of children or pets. If it is not possible to
install the units in safe places, it is necessary to provide safety protection systems (protective grids or similar) that
prevent children or pets from coming into contact with the units.
Indoor units must be securely attached to the wall or ceiling. The block or ceiling to which they are attached must
be able to support the load generated by the units.
63