ABB CP-C-Serie Betriebs- Und Montageanleitung Seite 16

Type
rigid
stripping length
tighening torque
Electrical connection - output side
Wire size
fine-strand wire with wire end ferrule
fine-strand wire without wire end ferrule
rigid
stripping length
tightening torque
Minimum distance to other units
horizontal / vertical
Degree of protection, enclosure / terminals
Material of enclosure
Protection class ( EN 61140)
Environmental data
Ambient temperature range
Damp heat (IEC/EN 60068-2-3)
Pollution category (EN 50178)
Climatic category (IEC/EN 60721)
Mounting
Mounting position
Vibration (IEC/EN 60068-2-6)
Shock (IEC/EN 60068-2-27)
Isolation data
Insulation voltage:
Standards
Product standard
Low Voltage Directive
EMC directive
Electrical safety
Protective low voltage
Electromagnetic compatibility
Interference immunity
electrostatic discharge (ESD)
electromagnetic field
fast transient (Burst)
powerful impulses (Surge)
HF line emission
Interference emission
electromagnetic field
HF line emission
Additional information:
Power, input and output (I/O) wiring must be in accordance with Class I, Div. 2 wiring methods - Article 501-10(B) (1) of the
National Electrical Code.
- SUITABLE FOR USE IN CLASS I, DIVISION 2, GROUPS A, B, C, D OR NON-HAZARDOUS LOCATIONS ONLY.
- WARNING - EXPLOSION HAZARD - SUBSTITUTION OF COMPONENTS MAY IMPAIR SUITABILITY FOR CLASS I, DIVISION 2.
- WARNING - EXPLOSION HAZARD - DO NOT DISCONNECT EQUIPMENT UNLESS POWER HAS BEEN SWITCHED OFF OR THE AREA IS
KNOWN TO BE NON-HAZARDOUS.
CP-C 24/5.0
0.2 - 2.5 mm
pluggable connecting terminals, actuate only when the power is off
0.12 - 2.5 mm
0.12 - 2.5 mm
0.12 - 2.5 mm
enclosure shell - aluminium / cover - zinc-coated sheet steel
operation
full load
storage
input
input/PE
output/PE
CP-C 24/10.0
2 / 24 - 14 AWG
7 mm / 0.27 inches
0.4 Nm
2
/ 26 - 14 AWG
2 / 26 - 14 AWG
2
/ 26 - 14 AWG
8 mm / 0.315 inches
0.4 Nm
10 mm / 80 mm (0.39 in / 3.15 in)
IP 20 / IP 20
I
-25 ... +70
o
0 ... +60 C (without derating)
-40 ... +85
o
93 % at +40 C, no condensation
2
3K3
DIN rail (EN 50022), snap-on mounting
horizontal
3 kV AC (type test), 1.2 kV AC (routine test)
1.5 kV AC (type test), 1.2 kV AC (routine test)
350 V AC (routine test)
IEC/EN 61204
2006/95/EC
2004/108/EC
EN 50178, EN 60950, UL 60950, UL 508
SELV (EN 60950)
IEC/EN 61000-6-2
IEC/EN 61000-4-2, Level 4 - 8 kV / 15 kV
IEC/EN 61000-4-3, Level 3 - 10 V/m
IEC/EN 61000-4-4, Level 4 - 4 kV
IEC/EN 61000-4-5, Level 4 - 2 kV sym., Level 3 - 3 kV unsym.
IEC/EN 61000-4-6, Level 3 - 10 V
IEC/EN 61000-6-3
IEC/CISPR 22, EN 55022, Class B
IEC/CISPR 22, EN 55022, Class B
CP-C 24/20.0
0.5 - 16 mm 2 / 20 - 6 AWG
12 mm / 0.47 inches
1.2 - 1.5 Nm
2
2.5 - 10 mm / 14 - 8 AWG
0.5 - 10 mm 2 / 20 - 8 AWG
2
0.5 - 16 mm / 20 - 6 AWG
12 mm / 0.47 inches
1.2 - 1.5 Nm
o
C
o C
16