Functional Description - Makita AS001G Betriebsanleitung

Installing and removing deflating
nozzles and attachments
Optional accessory
NOTICE:
Always be sure to install and uninstall
deflating nozzles and attachments only while the
air vent hose complete is disconnected from the
tool. Handling the air vent hose complete assembled
into the tool may cause the tool to stand unstable
resulting in it falling over.
1.
Align the guide projections on the pinch valve
nozzle with the locking notches on the lock sleeve of the
air vent hose complete, then push the pinch valve noz-
zle firmly into the lock sleeve until it locks in place with a
click.
► Fig.10: 1. Pinch valve nozzle 2. Guide projections
3. Locking notches 4. Lock sleeve 5. Air
vent hose complete
Optional rubber attachments
Optional rubber attachments require to be placed over
the nozzle. Be careful not to attach rubber attachments
directly to the air vent hose complete.
i Align the guide projections on the nozzle 13 with
the locking notches on the lock sleeve of the air vent
hose complete, then push the nozzle firmly into the lock
sleeve until it locks in place with a click.
ii Place a rubber attachment over the nozzle head
by pushing and hand screwing it in place.
► Fig.11: 1. Rubber attachments 2. Nozzle 13 3. Air
vent hose complete
NOTICE:
Make sure that the nozzle has been
correctly attached to the air vent hose complete
so the guide projections on the nozzle neatly fit
into the locking notches on the lock sleeve.
2. Turn the dust cap on the suction inlet at the rear of
the housing counterclockwise to take the dust cap out
of the housing. Two locking tabs on the dust cap can be
disengaged by aligning them with the guide grooves on
the housing.
► Fig.12: 1. Dust cap 2. Locking tabs 3. Suction inlet
4. Guide grooves
3. Attach the end of the air vent hose complete to
the suction inlet, aligning the two locking tabs on the
air vent hose complete with the guide grooves on the
housing. Then hold and turn the rear cuffs of the air vent
hose complete clockwise to secure it in place.
► Fig.13: 1. Air vent hose complete 2. Rear cuffs
3. Suction inlet 4. Locking tabs 5. Guide
grooves
4. To remove the deflating nozzle and attachments,
follow the installation steps in reverse.
NOTICE:
Always hold and turn the rear cuffs of
the air vent hose complete to install and uninstall
the air vent hose complete in place.
Installing optional filter
Optional accessory
An optional high performance filter (Filter C) is available
for restricting dust intake into the motor under dusty
working conditions.
1.
Turn the dust cap on the suction inlet at the rear of
the housing counterclockwise to take the dust cap out of the
housing. Two locking tabs on the dust cap can be disengaged
by aligning them with the guide grooves on the housing.
► Fig.14: 1. Dust cap 2. Locking tabs 3. Suction inlet
4. Guide grooves
2.
Replace an optional high performance filter on the
suction inlet, aligning the two locking tabs on the optional
filter with the guide grooves on the housing. Then turn the
optional filter clockwise to secure it in place.
► Fig.15: 1. Optional high performance filter 2. Locking
tabs 3. Suction inlet 4. Guide grooves
NOTICE:
An optional high performance filter
(Filter C) can be reused many times by cleaning it
out. Clean dust off the filter regularly as a clogged
filter may block the airflow and cause less effi-
cient operation. Occasionally wash the filter in
water, rinse and dry thoroughly in the shade
before use.
NOTICE:
Do not wipe, rub or scratch an optional
high performance filter (Filter C) hardly. Be sure
to shake or blow dust off the filter with care.
FUNCTIONAL
DESCRIPTION
CAUTION:
Always be sure that the tool is
switched off and the battery cartridge is removed
before adjusting or checking function on the tool.
Installing or removing battery
cartridge
CAUTION:
Always switch off the tool before
installing or removing of the battery cartridge.
CAUTION:
Hold the tool and the battery car-
tridge firmly when installing or removing battery
cartridge. Failure to hold the tool and the battery
cartridge firmly may cause them to slip off your hands
and result in damage to the tool and battery cartridge
and a personal injury.
► Fig.16: 1. Red indicator 2. Button 3. Battery
cartridge
To remove the battery cartridge, slide it from the tool
while sliding the button on the front of the cartridge.
To install the battery cartridge, align the tongue on the
battery cartridge with the groove in the housing and slip
it into place. Insert it all the way until it locks in place
with a little click. If you can see the red indicator as
shown in the figure, it is not locked completely.
16 ENGLISH