Adjusting The Bevel Angle - Makita LS0816F Betriebsanleitung

10. Tighten the rear screws (do not tighten firmly).
11. Release the stopper pin for handle lock and raise
the handle. Then tighten all the screws securely.
NOTICE:
After setting the bevel angle, ensure
that the kerf boards are adjusted properly. Correct
adjustment of the kerf boards helps to provide proper
support of the workpiece and minimizing workpiece
tear out.
Maintaining maximum cutting
capacity
This tool is factory adjusted to provide the maximum
cutting capacity for a 216 mm circular saw blade.
When installing a new circular saw blade, always check
the lower limit position of the circular saw blade, and if
necessary, adjust it as follows:
1. Unplug the tool. Then, push the carriage toward
the guide fence fully and lower the handle completely.
2. Use the hex wrench (screwdriver side) to turn the
adjusting bolt until the circular saw blade comes slightly
below the cross section of the guide fence and the top
surface of the turn base.
► Fig.14: 1. Adjusting bolt 2. Guide fence
► Fig.15
3. Rotate the circular saw blade by hand while
holding the handle all the way down to be sure that
the circular saw blade does not contact any part of the
lower base. Re-adjust the maximum cutting capacity, if
necessary.
WARNING:
After installing a new circular saw
blade and with the tool is unplugged, always be
sure that the circular saw blade does not contact
any part of the lower base when the handle is
lowered completely. If the circular saw blade con-
tacts with the base, it may cause kickback and result
in serious personal injury.
► Fig.16
Stopper arm
The lower limit position of the saw blade can be easily
adjusted with the stopper arm. To adjust the lower limit, turn
the stopper arm in the direction of the arrow as shown in the
figure. Turn the adjusting screw so that the saw blade stops
at the desired position when lowering the handle fully.
► Fig.17: 1. Stopper arm 2. Adjusting screw
Adjusting the miter angle
CAUTION:
After changing the miter angle,
always secure the turn base by tightening the grip
firmly.
NOTICE:
When turning the turn base, be sure to
raise the handle fully.
Rotate the grip counterclockwise to unlock the turn
base. Turn the grip while holding up the lock lever to
move the turn base. Align the pointer with your desired
angle in the miter angle scale then tighten the grip.
► Fig.18: 1. Lock lever 2. Grip 3. Pointer
Positive stop function
This miter saw employs positive stop function. You can
set 0°, 15°, 22.5°, 31.6°, and 45° right/left miter angle
quickly. To use this function, move the turn base close
to your desired positive stop angle while holding up the
lock lever. Then release the lock lever and move the
turn base to your desired positive stop angle until the
turn base is locked.

Adjusting the bevel angle

CAUTION:
After changing the bevel angle,
always secure the arm by tightening the lever
clockwise.
NOTICE:
Always remove vertical vise before
adjusting the bevel angle.
NOTICE:
When tilting the circular saw blade, be
sure that the carriage is fully raised.
NOTICE:
When changing bevel angles, be sure
to reposition the kerf boards appropriately as
explained in the section for positioning kerf
boards.
NOTICE:
Do not tighten the lever too hard. Doing
so may cause malfunction of the locking mecha-
nism of the bevel angle.
Tilting the circular saw blade to the
left 0° - 45°
1. Rotate the lever counterclockwise.
2. Hold the handle and tilt the carriage to the left.
3. Align the pointer with your desired angle in the
bevel angle scale.
4.
Tighten the lever clockwise to secure the arm.
► Fig.19: 1. Lever 2. Handle 3. Pointer 4. Bevel angle
scale
Tilting the circular saw blade beyond
the left 0° - 45°
1. Rotate the lever counterclockwise.
2. Hold the handle and set the carriage at 0° for right
2° side, or 45° for left 47° side.
3. Tilt the carriage slightly to opposite side.
4.
Push the releasing button.
5.
Tilt the carriage to the desired position beyond the
range 0° - 45°.
6. Tighten the lever clockwise to secure the arm.
When tilting the carriage to the right 2°
► Fig.20: 1. Lever 2. Handle 3. Releasing button
When tilting the carriage to the left 47°
► Fig.21: 1. Lever 2. Handle 3. Releasing button
19 ENGLISH