Herunterladen Inhalt Inhalt Diese Seite drucken

DJI AIR 3 Bedienungsanleitung Seite 4

Vorschau ausblenden Andere Handbücher für AIR 3:
Inhaltsverzeichnis

Werbung

EN
Warnings
1. Place the charging hub on a flat, stable surface with
good ventilation when charging an external device
or accumulating power. Make sure the device is
properly insulated to prevent fire hazards.
2. DO NOT attempt to touch the metal terminals on
the battery ports. Clean the metal terminals with a
clean, dry cloth if there is any noticeable buildup.
3. Make sure to charge batteries with low battery
power in time. It is recommended to store the
batteries in the charging hub. The charging hub
automatically checks the battery power every
seven days. When a battery has 0% power level, the
battery with a high power level will charge the low
power level battery until its power reaches 5% to
prevent over-discharging.
Introduction
TM
The DJI
Air 3 Battery Charging Hub is designed to
charge up to three Intelligent Flight Batteries. After the
Intelligent Flight Batteries are installed, the charging
hub can supply power to external devices via the USB-C
port, such as remote controllers or mobile phones. The
charging hub can also use the power accumulation
function to transfer the remaining power of multiple
low-power batteries into the battery with the highest
remaining power.
Usage
Charging Intelligent Flight Battery
1. Insert the batteries into the charging hub until it
clicks into place. (Figure A1)
2. Connect the charging hub to a power outlet using
a USB-C charger. The Intelligent Flight Battery with
the highest power level will be charged first, and
then the rest will be charged in sequence according
to their power levels. The status LED indicates the
battery level during charging. Refer to the Status LED
Descriptions for more information about the blinking
patterns of the status LED.
3. The battery can be stored in the charging hub after
charging. Remove the battery from the charging
hub for use. (Figure A2)
Using Charging Hub as a Power Bank
1. Insert an Intelligent Flight Battery into the charging
hub. Connect an external device via the USB-C
port, such as a mobile phone or remote controller.
(Figure B)
2. Press the function button, and the status LED of the
charging hub turns solid green. The battery with the
lowest power level will be discharged first, followed by
the remaining batteries to be discharged sequentially.
To stop charging the external device, disconnect the
external device from the charging hub.
If the remaining charge of a battery is lower
than 7%, the battery cannot charge the
external device.
Accumulating Power
1. Insert more than one battery into the charging hub,
and press and hold the function button until the status
LED turns green. The status LED of the charging hub
pulses green, and the charge is transferred from the
battery with the lowest power level to the battery with
the highest power level.
2. To stop accumulating power, press and hold the
function button until the status LED turns yellow. After
stopping power accumulation, press the function
button to check the power level of the batteries.
Power accumulation stops automatically in the
following situations:
a. The receiving battery is fully charged, or the
power of the output battery is lower than 5%.
b. A charger or external device is connected to
the charging hub or any battery is inserted
or withdrawn from the charging hub during
power accumulation.
c. Power accumulation is interrupted for more
than 15 minutes due to abnormal battery
temperature.
After accumulating power, charge the battery
with the lowest power level as soon as
possible to avoid discharge.
Status LED Descriptions
Blinking Pattern
Description
Solid yellow
The charging hub is idle
Charging the battery or
Pulses green
accumulating power
All batteries fully charged or
Solid green
supplying power to external
devices
Temperature of the batteries is
Blinks yellow
too low or too high (no further
operation needed)
Power supply error or battery
error (remove and reinsert the
Solid Red
batteries or unplug and plug in
the charger)
Specifications
Product Model
CHX233-100
DJI 100W USB-C Power Adapter,
Compatible
DJI 65W Portable Charger, or
Power Adapter
other USB PD chargers or PPS
chargers
Compatible
BWX233-4241-14.76
Battery Model
Dimensions
170.6×48.3×112.8 mm
Weight
169 g
Operating
5° to 40° C (41° to 104° F)
Temperature
Input (USB-C)
5-20 V, Max. 5 A
5V
Output (USB-C)
15V
DJI 100W USB-C Power Adapter:
Approx. 60 mins
Charging Time
DJI 65W Portable Charger: Approx.
(Single Battery)
80 mins
3A, 9V
5A, 12V
5A,
5A, 20V
4.1A
3

Werbung

Inhaltsverzeichnis
loading

Inhaltsverzeichnis