Using The Shaver - Braun CT6cc Bedienungsanleitung

Shaver display
Charge status
During charging the symbol in the on/off switch (5)
blinks green. When fully charged, it will light up for a
few seconds, provided the shaver is connected to an
electrical outlet.
Low charge
The symbol in the on/off switch (5) shines red when
the battery is running low. You should be able to
finish your shave. When switching off the shaver a
beep sound reminds you of the low charge status.
Cleaning Status (only models CT6cc/CT5cc/
CT4cc/CT3cc/CT2cc)
The cleaning indicator
needs to be cleaned in the Clean&Charge station.
Travel lock
The lock symbol lights up when the shaver has
been locked to avoid unintended starting of the
motor (e.g. for storing it in a suitcase).

Using the shaver

Press the on/off switch (5) to operate the shaver.
Tips for a perfect dry shave
For best results, Braun recommends you to follow
3 simple steps:
1. Always shave before washing your face.
2. At all times, hold the shaver at right angles
(90°) to your skin.
3. Stretch your skin and shave against the
direction of your beard growth.
Cooling
Note: The cooling sensation experienced may differ
from person to person. It is influenced by personal
and environmental factors (e.g. skin, environmental
temperature).
Activation: To activate the cooling function, press
the cooling switch (3) during shaving. The symbol
in the cooling switch shines blue. For best cooling
performance, we recommend to wait a few seconds
after the cooling function has been activated.
Then continue shaving as usual.
Low battery: The symbol
starts blinking when the battery is running low and
there is not enough energy left for the cooling func-
tion. You should be able to finish your shave with
activated cooling function.
You can deactivate the cooling function by pressing
the cooling switch again.
12
lights up, when the shaver
(see fig. A)
in the cooling switch (3)
Long hair trimmer
To trim sideburns, moustache or beard, press the
release button (8) and slide the long hair trimmer (6)
upwards.
Travel lock
• Activation: By pressing the on/off switch (5) for
3 seconds the shaver is locked. This is confirmed
by a beep sound and the lock symbol
display. Afterwards the display turns off.
• Deactivation: By pressing the on/off switch for
3 seconds the shaver is unlocked again.
Manual cleaning of the shaver
(see fig. C/D)
The shaver is suitable for cleaning under running tap
water. Detach the shaver from the power supply
before cleaning it in water.
• Switch the shaver on and rinse the shaver head
under hot running water. You may use liquid soap
without abrasive substances. Rinse off all foam
and let the shaver run for a few more seconds.
• Next, switch off the shaver, remove the Foil &
Cutter cassette and let it dry.
• If you regularly clean the shaver under water, then
once a week apply a drop of light machine oil on
top of the Foil & Cutter cassette.
Alternatively, you may clean the shaver using a brush:
• Switch off the shaver. Remove the Foil & Cutter
cassette (1) and tap it out on a flat surface. Using
a brush, clean the inner area of the pivoting head.
Do not clean the cassette with the brush as this
may damage it!
Clean&Charge station
(models CT6cc/CT5cc/CT4cc/CT3cc/CT2cc)
The Clean&Charge station has been developed for
cleaning, charging, lubricating, disinfecting and
storing your Braun shaver.
13 Station power socket
14 Lift button for cartridge exchange
15 Station-to-shaver contacts
16a Level indicator
16b Status light
17 Start button
18 Cleaning cartridge
Installing the Clean&Charge station (see fig. E)
• Remove the protection foil from the Clean&Charge
station display.
• Press the lift button (14) at the rear side of the
Clean&Charge station to lift up the housing.
• Hold the cleaning cartridge (18) down on a flat,
stable surface (e.g. table).
in the