Using The Shaver - Braun CoolTec CT6cc Bedienungsanleitung

or for models CT6cc/CT5cc/CT4cc/CT3cc/
CT2cc the Clean&Charge station (see Chapter
«Clean&Charge station»).
Note: The shaver can only be charged via the
charging shell or the Clean&Charge station.
Models CT4s/CT2s must not be used with the
Clean&Charge station.
Charging shell (see fig. B)
• Click the charging shell (12a) onto the stand (12c
- models CT4s/CT2s only). Using the special cord
set (10), connect the shell power socket (12b) to
an electrical outlet.
• Place the shaver into the charging shell. The
contacts (7) on the back of the shaver need to
align with the contacts (12d) in the charging shell.
A beep sound confirms that the shaver sits prop-
erly in the station.
• The shaver will be automatically charged.
Charging and basic operating information
• A full charge provides the following operating
times according to your beard growth and
environmental temperatures:
– ca. 45 minutes without activated cooling
function
– ca. 15 minutes with activated cooling function;
afterwards 20 minutes operating time without
cooling function.
• Recommended ambient temperature for charging
is 5 °C to 35 °C. The battery may not charge properly
or at all under extreme low or high temperatures.
Recommended ambient temperature for shaving
is 15 °C to 35 °C.
• Do not expose the appliance to temperatures
higher than 50 °C for extended periods of time.
• When the shaver is connected to an electrical
outlet, it may take some minutes until the display
illuminates.
Shaver display
Charge status
During charging the symbol in the on/off switch (5)
blinks green. When fully charged, it will light up for a
few seconds, provided the shaver is connected to an
electrical outlet.
Low charge
The symbol in the on/off switch (5) shines red when
the battery is running low. You should be able to
finish your shave. When switching off the shaver a
beep sound reminds you of the low charge status.
Cooling Status
The symbol shines blue with activated cooling
function. When the battery is running low it starts
blinking.
12
All manuals and user guides at all-guides.com
Cleaning Status (only models CT6cc/CT5cc/
CT4cc/CT3cc/CT2cc)
The cleaning indicator
needs to be cleaned in the Clean&Charge station.
Travel lock
The lock symbol
been locked to avoid unintended starting of the
motor (e.g. for storing it in a suitcase).

Using the shaver

Press the on/off switch (5) to operate the shaver.
Tips for a perfect dry shave
For best results, Braun recommends you to follow
3 simple steps:
1. Always shave before washing your face.
2. At all times, hold the shaver at right angles
3. Stretch your skin and shave against the
Cooling
Note: The cooling sensation experienced may differ
from person to person. It is influenced by personal
and environmental factors (e.g. skin, environmental
temperature).
Activation: To activate the cooling function, press
the cooling switch (3) during shaving. The symbol
in the cooling switch shines blue. For best cooling
performance, we recommend to wait a few seconds
after the cooling function has been activated.
Then continue shaving as usual.
Low battery: The symbol
starts blinking when the battery is running low and
there is not enough energy left for the cooling func-
tion. You should be able to finish your shave with
activated cooling function. We recommend to
charge the appliance afterwards to have the cooling
function available for the next shave.
You can deactivate the cooling function by pressing
the cooling switch again.
Long hair trimmer
To trim sideburns, moustache or beard, press the
release button (8) and slide the long hair trimmer (6)
upwards.
Travel lock
• Activation: By pressing the on/off switch (5) for
• Deactivation: By pressing the on/off switch for
lights up, when the shaver
lights up when the shaver has
(see fig. A)
(90°) to your skin.
direction of your beard growth.
3 seconds the shaver is locked. This is confirmed
by a beep sound and the lock symbol
display. Afterwards the display turns off.
3 seconds the shaver is unlocked again.
in the cooling switch (3)
in the