Starting Operation; Working Advice; Maintenance And Service; Maintenance And Cleaning - Bosch GST 150 CE Professional Originalbetriebsanleitung

Starting Operation

Pay attention to the mains voltage. The voltage of the
u
power source must match the voltage specified on the
rating plate of the power tool. Power tools marked
with 230 V can also be operated with 220 V.
Switching On and Off (GST 150 CE)
Make sure that you are able to press the On/Off switch
u
without releasing the handle.
To switch on the power tool, slide the on/off switch (2) for-
wards so that "I" appears on the switch.
To switch off the power tool, slide the on/off switch (2)
backwards so that "0" appears on the switch.
Switching On and Off (GST 150 BCE)
Make sure that you are able to press the On/Off switch
u
without releasing the handle.
To switch on the power tool, press the on/off switch (2).
To lock the on/off switch (2), keep it pressed down and
push the locking mechanism (1) to the right or left.
To switch off the power tool, release the on/off switch (2).
If the on/off switch (2) is locked, press the switch first and
then release it.
Constant Electronic control
The Constant Electronic control keeps the stroke rate at no
load and under load virtually consistent, guaranteeing uni-
form performance.
Controlling the stroke rate (GST 150 BCE)
You can variably adjust the stroke rate of the power tool
when it is on by pressing in the on/off switch (2) to varying
extents.
Applying light pressure to the on/off switch (2) results in a
low stroke rate. Applying increasing pressure to the switch
increases the stroke rate.
Preselect the stroke rate
You can also preselect the stroke rate and change it during
operation using the stroke rate preselection thumbwheel
(3).
The required stroke rate is dependent on the material and
the work conditions and can be determined using practical
tests.
It is recommended that you reduce the stroke rate when
placing the saw blade on the workpiece and when sawing
plastic and aluminium.
During prolonged periods of use at a low stroke rate, the
power tool may heat up significantly. Remove the saw blade
and let the power tool run at the maximum stroke rate for
around three minutes to cool down.

Working Advice

Pull the plug out of the socket before carrying out any
u
work on the power tool.
Switch the power tool off immediately if the saw blade
u
becomes blocked.
Bosch Power Tools
When machining small or thin workpieces, always use
u
a stable base or saw table (accessory).
Before sawing into wood, chipboard, building materials,
etc., check for and remove any foreign objects such as nails,
screws, etc.
Plunge cutting (see figure H)
Plunge cuts may only be applied to soft materials,
u
such as wood, gypsum board, etc.
For plunge cutting, use only short saw blades. Plunge cutting
is possible only with a mitre angle of 0°.
Place the power tool so that the front edge of the base plate
(5) rests on the workpiece, without the saw blade (10)
touching the workpiece, and switch it on. On power tools
with stroke rate control, select the maximum stroke rate.
Press the power tool firmly against the workpiece and allow
the saw blade to plunge slowly into the workpiece.
As soon as the base plate (5) rests fully on the workpiece,
continue sawing along the required cutting line.
Parallel guide with circle cutter (accessory)
When working with the parallel guide with circle cutter (23)
(accessory), the workpiece must be no more than 30 mm
thick.
Parallel cuts (see figure J): Loosen the locking screw (22)
and slide the scale on the parallel guide through the guide
(21) in the base plate. Adjust the desired cutting width as a
scale value on the inside edge of the base plate. Retighten
the locking screw (22).
The parallel guide can also be used in combination with the
guide rail (24) (accessory, see figure K).
Circular cuts (see figure L): Drill a hole large enough to push
the saw blade through on the cutting line within the circle to
be cut. Machine the drill hole with a router or file so that the
saw blade can lie flush with the cutting line.
Position the locking screw (22) on the other side of the par-
allel guide. Slide the scale on the parallel guide through the
guide (21) into the base plate. Drill a hole in the workpiece
in the middle of the section to be cut out. Insert the centring
tip (25) through the inner opening of the parallel guide and
into the drilled hole. Adjust the radius as a scale value on the
inside edge of the base plate. Retighten the locking screw
(22).
Coolant/lubricant
As the material heats up along the cutting line when cutting
metal, you should apply coolant or lubricant.

Maintenance and Service

Maintenance and Cleaning

Pull the plug out of the socket before carrying out any
u
work on the power tool.
To ensure safe and efficient operation, always keep
u
the power tool and the ventilation slots clean.
In order to avoid safety hazards, if the power supply cord
needs to be replaced, this must be done by Bosch or by an
English | 19
1 609 92A 85Z | (05.08.2022)