Technical Data; Noise/Vibration Information - Bosch GKF 1600 CE Professional Originalbetriebsanleitung

(52) Release lever for guide-bushing adapter
(53) Guide bushing
(54) Fastening screw for guide plate
(55) Centring pin
(56) Fastening screws for non-plunge base

Technical Data

Router/contour router
Article number
Rated power input
No-load speed
Speed preselection
Constant electronic control
Connection for dust extraction
Compatible collets
Router cage stroke
Weight according to EPTA‑Procedure 01:2014
Protection class
The specifications apply to a rated voltage [U] of 230 V. These specifications may vary at different voltages and in country-specific models.

Noise/Vibration Information

Noise emission values determined according to
EN 62841-2-17.
Typically the A-weighted noise level of the power tool are:
86 dB(A); sound power level 97 dB(A). Uncertainty K =
3 dB.
Wear hearing protection!
GOF 1600 CE: Vibration total values a
and uncertainty K determined according to EN 62841-2-17:
2 2
a = 5.5 m/s , K = 1.5 m/s .
h
GOF 1600 CE: Vibration total values a
and uncertainty K determined according to EN 62841-2-17:
2 2
a = 6 m/s , K = 1.5 m/s .
h
The vibration level and noise emission value given in these
instructions have been measured in accordance with a
standardised measuring procedure and may be used to com-
pare power tools. They may also be used for a preliminary
estimation of vibration and noise emissions.
The stated vibration level and noise emission value repres-
ent the main applications of the power tool. However, if the
power tool is used for other applications, with different ap-
plication tools or is poorly maintained, the vibration level
and noise emission value may differ. This may significantly
increase the vibration and noise emissions over the total
working period.
To estimate vibration and noise emissions accurately, the
times when the tool is switched off or when it is running but
not actually being used should also be taken into account.
This may significantly reduce vibration and noise emissions
over the total working period.
Bosch Power Tools
(57) Specialty hex key for routing depth fine adjustment
(58) Extraction hood for edge routing
(59) Fastening screw for extraction hood
a) Accessories shown or described are not included with the
a)
product as standard. You can find the complete selection of
accessories in our accessories range.
Implement additional safety measures to protect the oper-
ator from the effects of vibration, such as servicing the
power tool and application tools, keeping their hands warm,
and organising workflows correctly.
Fitting
Pull the plug out of the socket before carrying out any
u
work on the power tool.
(triax vector sum)
h
Inserting the routing motor into the plunge base/
non-plunge base (see figures A–B)
(triax vector sum)
h
Open the clamping lever for the plunge base/non-plunge
base (22).
Push the routing motor all the way into the plunge base/non-
plunge base.
When using the non-plunge base (3), press the clamping
lever (25) and slide the routing motor (1) up or down to the
required position in the non-plunge base (3), until it, with
the clamping lever (25) released, engages in one of the
three notches (26).
Close the clamping lever of the plunge base/non-plunge
base (22).
Set the required routing depth (see "Setting the routing
depth", page 23).
Separating the routing motor from the plunge unit/non-
plunge base (see figure C)
Open the clamping lever for the plunge base/non-plunge
base (22).
a)
(non-plunge base)
GOF 1600 CE
3 601 F24 0..
W 1600
−1
min 10000–25000
●
●
●
mm 8–12
inches ¼–½
mm 76
kg 5.8
/II
1 609 92A 57S | (16.04.2021)
English | 21
a)
a)
GKF 1600 CE
3 601 F24 0..
1600
10000–25000
●
●
●
8–12
¼–½
–
4.3
/II