Kärcher B 150 R Bedienungsanleitung Seite 22

vents, hydrochloric acid and hydrofluoric
acid.
Follow the safety instructions for using de-
tergents.
Note:
Do not use highly foaming detergents.
Application
Routine cleaning of all water
resistant floors
Routine cleaning of glossy
surfaces (e.g. granite)
Routine cleaning and basic
cleaning of industrial floors
Routine cleaning and basic
cleaning of fine stoneware
tiles
Routine cleaning of tiles in
sanitary areas
Cleaning and disinfection in
sanitary areas
Removal of coating from all
alkali-resistant floors (e.g.
PVC)
Removal of coating from li-
noleum floors
Fresh water
 Open the cover of the fresh water reser-
voir.
 Fill fresh water (max. 60 °C) until 15 mm
below the upper edge of the tank.
 Pour in detergent.
Note:
If detergent is added to the detergent tank
first before the water, this can result in a for-
mation of a lot of foam.
 Close the cover of the fresh water res-
ervoir.
Note:
Fill up the fresh water tank completely prior
to the initial start-up to bleed the water pipe
system.
Filling system (optional)
 Connect the water hose to the connec-
tion neck on the filling system.
 Open the water supply.
Once the maximum fill level is reached,
the built-in floater valve will stop the wa-
ter inflow.
 Shut off water supply.
 Remove the water hose.
Metering system (only Dose model)
Detergent is added to the fresh water on
the way to the cleaning head with the help
of a dosaging device.
 Place the detergent bottle into the de-
vice.
 Close the bottle lid.
 Insert the suction hose of the dosaging
equipment into the bottle.
Note:
The dosing unit can be used to add 3% de-
tergent at maximum. With higher dosage
the detergent must be put into the fresh wa-
ter tank.
ATTENTION
Risk of clogging due to dried detergent
when the detergent is added to the fresh
water tank of the Dose version. The flow
22
meter of the dosing equipment can aggluti-
nate on account of drying detergent and
hamper the functioning of the dosing equip-
ment. Subsequently rinse the fresh water
tank and the appliance with clear water. For
rinsing, select cleaning programme with
application of water at the programme se-
Detergent
lector switch. Set the water quantity to the
RM 746
highest value, set the detergent dosage to
RM 780
0%
RM 755 es
Note:
The appliance is equipped with a fresh wa-
RM 69 ASF
ter indicator in the display. If the fresh water
tank is empty, the function of adding deter-
RM 753 gent gets deactivated. The cleaning head
continues to work without liquid supply.
Setting the parameters
RM 751
With yellow Intelligent Key
Parameters for the different cleaning pro-
RM 732
grammes are preset in the appliance.
Depending on the authorisation of the yel-
RM 752
low Intelligent Key, individual parameters
can be changed.
The modification of the parameters is only
RM 754
valid until another cleaning programme is
selected via the programme selection
switch.
If you wish to permanently change the pa-
rameters, you must use a grey Intelligent
Key. This adjustment procedure is de-
scribed in the section "Grey Intelligent
Key".
Note:
Almost all displayed texts regarding param-
eter settings are self-explanatory. The only
exception is the FACT Parameter (R clean-
ing head only):
Fine Clean: Lower brush speed for re-
–
moving the grey film on fine stone
floors.
Whisper Clean: Medium brush speed
–
for regular cleaning with reduced noise
level.
Power Clean: High brush speed for pol-
–
ishing, crystallising and sweeping.
 Turn the program selection switch to
the desired cleaning program.
 Turn the info button until the desired pa-
rameter is displayed.
 Press Info button - the set value blinks.
 Set the desired value by turning the info
button.
 Confirm the changed setting by press-
ing the Info button or wait till the set val-
ue is automatically accepted after 10
seconds.
Setting the Vacuum Bar
Oblique position
To improve the vacuuming result on tiled
floors the vacuum bar can be turned to an
oblique position of up to 5°.
6
-
EN
 Release the wing nuts.
 Turn the vacuum bar.
 Tighten the wing nuts.
Inclination
If the vacuum result is unsatisfactory the in-
clination of the straight vacuum bar can be
modified.
1 Turning handle
2 Tension lever
 Lift the tension lever.
 Adjust the rotary handle to incline the
suction bar.
 Press the tension lever downwards.
Adjust wiping flaps
 Adjust the wiper flaps by turning the ad-
justment wheel so that they touch the
floor.
 Turn the adjustment wheel an addition-
al turn toward the bottom.
Spray nozzle (option)
The hose with the spray nozzle is attached
to the back of the appliance. It serves for
washing away dirt and for manual cleaning
of the wastewater tank.
 Turn programme selector switch to
"transport run".
 Press Info button.
 Turn the info button until "tank rinsing"
is shown on the display.
 Press Info button.
 Turn the info button until "ON" is dis-
played.
 Press Info button.
The water pump delivers fresh water
through the spray nozzle.