Kärcher B 150 R Bedienungsanleitung Seite 21

 Place the boards on the edge of the pal-
let. Place the boards in such a way that
they lie in front of the four wheels of the
machine. Fasten the boards with
screws.
 Slide the four support beams included
in the packaging under the ramp.
 Remove the wooden bars in front of the
wheels.
1 Lever
2 brake
 Pull the brake lever and insert a coin
between the lever and the brake.
 Slowly push the machine down from the
ramp.
DANGER
Danger of accident due to lacking braking
effect.
 Remove the coin immediately after
pushing the device.
or
 Plug in the Intelligent Key.
 Bring the safety switch into the "1" posi-
tion.
 Set programme selector switch to trans-
port run.
 Set the travel direction switch to "for-
ward".
 Actuate the accelerator pedal.
 Drive the appliance off the pallet.
 Bring the safety switch into the "0" posi-
tion.
Install cleaning head
The procedure for changing the cleaning
head is described in the chapter "Mainte-
nance Tasks".
Note:
On some models, the cleaning head is al-
ready installed.
Installing the Brushes
The installation of the brushes is described
in the chapter "Maintenance Tasks".
Installing the Vacuum Bar
 Insert the vacuum bar into the vacuum
bar suspension in such a manner that
the profiled sheet is positioned above
the suspension.
 Tighten the wing nuts.
 Insert the suction hose.
Operation
DANGER
Risk of injuries. Never use the unit without
protective roof in areas where the opera-
tors can be hit by dropping objects.
Note:
To take all functions out of operation imme-
diately, bring the safety switch into the "0"
position.
 Carry out maintenance work before
starting work (see "Care and mainte-
nance").
Adjusting driver's seat
 Operate the lever for the seat adjust-
ment and move the seat to the desired
position.
 Release the seat adjustment lever and
lock the seat in place.
Turning on the Appliance
 Take the seating position.
 Plug in the Intelligent Key.
 Bring the safety switch into the "1" posi-
tion.
 Turn the programme switch to the de-
sired function.
 If the relevant indication appears on the
display, perform the maintenance task.
Display Activity
Maintenance Clean the vacuum bar.
Vacuum bar
Maintenance Clean the fresh water fil-
Fresh water Fil- ter.
ter
Maintenance Check vacuum lips for set-
Suction lip ting and wear and tear.
Maintenance Clean protective turbine
Turbine strainer strainer.
Maintenance Check brush for wear and
Brush head tear and clean it.
 Press Info button.
 Reset the counter for the corresponding
maintenance (see "Care and mainte-
nance/resetting counter").
Note:
If the counter is not reset, the maintenance
indicator appears again with every start-up
of the device.
5
-
EN
Check parking brake
DANGER
Danger of accident. The functionality of the
parking brake must be checked before
each use.
 Turn on the appliance.
 Set the travel direction switch to "for-
ward".
 Set programme selector switch to trans-
port run.
 Gently depress drive pedal.
 The brake must unlock audibly. The
machine must roll easily on a plane sur-
face. When the pedal is released, the
brake locks audibly. Switch off the ma-
chine and call the aftersales service if
the above-mentioned events do not oc-
cur.
Driving
DANGER
Danger of tipping when driving round
bends at high speed.
Danger of slipping on wet floors.
 Drive slowly when cornering.
Danger of tipping on unstable ground.
 Only use the machine on sound surfac-
es.
Danger of tipping with excessive sideways
tilt.
Driving
 Take the seating position.
 Plug in the Intelligent Key.
 Bring the safety switch into the "1" posi-
tion.
 Set programme selector switch to trans-
port run.
 Set the drive direction using the drive
direction button at the operator console.
 Determine the driving speed by press-
ing the drive pedal.
 Stop the machine: Release the drive
pedal.
Note:
The direction of travel can also be changed
while driving. This way even very dull spots
can be polished by driving back and forth
several times.
Overload
In case of overloading, the drive motor au-
tomatically switches off after a certain peri-
od. A fault message is displayed on the
console. The concerned unit gets switched
off if the controls get overheated.
 Allow machine to cool down at least for
15 minutes.
 Turn the programme switch to "OFF",
wait for a short period of time and turn it
back to the desired programme.
Filling in detergents
Detergent
ATTENTION
Risk of damage. Only use the recommend-
ed detergents. With respect to different de-
tergents the operator bears the increased
risk regarding the operational safety and
danger of accident.
Only use detergents that are free from sol-
21