Guarantee Provisions; Technical Data - Niko 05-341 Bedienungsanleitung

05-340 / 05-341
3.3. Adding transmitters
You can program additional transmitters (max. 32) on a receiver at all times. Therefore, repeat '3.2. Programming'.
If the LED blinks fast for 2s, this means the transmitter has already been programmed. The receiver will stay in
programming mode, so another transmitter can be programmed.
3.4. Reset
- Press the flush key on the receiver (see '3.2. Programming') for more than 1,6s. (blinking LED).
- Press again for more than 1,6s.
- The receiver's memory is now completely erased. This is acknowledged by a long light signal (4s.).
- End RESET at any time by briefly pressing the flush key (< 1,6s.). Once you have completed RESET, it will
be automatically terminated.
3.5. Erasing selectively
- Press the flush key on the receiver for more than 1,6s.
- A light signal starts blinking (blinking LED).
- Press 1 of the control buttons of the transmitter you want to erase.
- The transmitter is erased from the memory, which is confirmed by a long light signal (2s.).
- If the LED blinks fast for 2s while erasing a transmitter, this means the transmitter had not yet been
programmed. The transmitter will stay in RESET, so another transmitter can be erased.
- End RESET at any time by briefly (<1,6s.) pressing the flush key again. Once you have completed RESET
or no key is pressed for 30s, RESET will be automatically terminated.
4. TROUBLESHOOTING
If, after programming, the system does not work, you can perform a number of extra checks.
4.1 New installation
- Check whether the protection between the battery and the contacts in the transmitter has been removed.
- Check whether the battery and the contacts make good permanent contact.
- Reset and (re)program the receiver.
- Press the programming key. The receiver is now in programming mode. The LED blinks and the load is
activated. If this is not the case, the receiver is defective.
- Program the transmitters with the receiver and end programming.
4.2. Existing installation
- Check the batteries of the transmitter(s).
- Check the operation of the connected receivers.
- Check for possible interference caused by changes in the system environment (moving of metal cabinets,
walls or furniture...). Restore the original condition, if possible.
4.3. Transmitter malfunction
Pick up the transmitter and walk towards the receiver.
- The system still works when holding the transmitter in your hand but not when the transmitter is mounted
on the wall: this may indicate the presence of moist or metal in the wall. In this case, move the transmitter.
- The system still works at reduced distance: the transmitter has been placed outside the transmitter range
or there is an interference problem. In this case, place the transmitter closer to the receiver or outside the
interference reach.
- The system does not work even when holding the transmitter close to the receiver: check the programming
and/or the battery of the transmitter (see above).
4.4. The system automatically switches on and off
- The system automatically switches on: this is only possible if a foreign transmitter was programmed in the receiver
within the receiver range. Reset the receiver and reprogram the relevant addresses (see '3.2. Programming').
- The system automatically switches off: this situation can be similar to the situation described above or be
the result of brief current interruptions.

5. TECHNICAL DATA

- transmitter range: 100m in open air; ±30m indoors
- no wiring between control points and receivers (RF controlled), only one connection between the switch-
receiver and the device to be operated.
- operating temperature: -10 to 35°C
- 1-channel receiver: 1 relay 10A, 230V 50Hz. Only suitable for mono-phase configurations. The contact
cannot be used for SELV-circuits.
LOAD TABLE
Load type
Resistive: incandescent lamps, halogen 230V~...
Inductive: low-voltage lighting via ferromagnetic transformers
(transformer loaded for at least 85%)
Non- or series-compensated fluorescent lamps
with ferromagnetic ballasts
Parallel-compensated fluorescent lamps with
ferromagnetic ballasts
Electronic control gear (HF-fluorescence ballasts,
electronic transformers...)
6. WARNINGS REGARDING INSTALLATION
• The installation should be carried out by a registered installer and in compliance with the statutory regulations.
• This user manual should be presented to the user. It should be included in the electrical installation file,
and it should be passed on to any new owners. Additional copies are available on the Niko website or via
the Niko support service.
• During installation, the following should be taken into account (non-exhaustive list):
- the statutory laws, standards and regulations.
- the technology currently available at the time of installation.
- this user manual, which only states general regulations and should therefore be read within the scope
of each specific installation.
- the rules of proper workmanship.
This product complies with all of the relevant European guidelines and regulations. If applicable, you can find
the EC declaration of conformity regarding this product at www.niko.eu.
nv Niko sa Industriepark West 40, BE-9100 Sint-Niklaas, Belgium — tel. +32 3 778 90 00 — fax +32 3 777 71 20 — e-mail: support@Niko.be — www.niko.be
7. NIKO SUPPORT
In case of doubt or for the specific exchange procedure in case of a possible defect, contact the Niko support
service in Belgium at +32 3 778 90 80 or your wholesaler/installer. Contact details and more information can
be found at www.niko.eu under the "Help and advice" section.

8. GUARANTEE PROVISIONS

• The period of guarantee is four years from the date of delivery. The delivery date is the invoice date of
purchase of the product by the consumer. If there is no invoice, the date of production applies.
• The consumer is obliged to inform Niko in writing about the non-conformity, within two months after
stating the defect.
• In case of a non-conformity, the consumer only has the right to a product repair or replacement free of
charge, which shall be decided by Niko.
• Niko shall not be held liable for a defect or damage resulting from incorrect installation, improper or careless
use, incorrect operation, transformation of the product, maintenance that does not adhere to the maintenance
instructions or an external cause, such as damage due to moisture or overvoltage.
• The compulsory regulations of the national legislation concerning the sale of consumer goods and the
protection of the consumer in the countries where Niko sells, directly or via sister companies, subsidiaries,
chain stores, distributors, agents or permanent sales representatives, take priority over the above-mentioned
rules and regulations.
Hereby, Niko nv declares that the radio equipment type 05-340 and 05-341 is in compliance with Directive
1999/5/EC and Directive 2014/53/EU.The full text of the EU declaration of conformity is available at www.niko.eu.
Do not dump this product with the unsorted waste. Bring it to a recognised waste collection point. Together with producers
and importers, you have an important role to play in the advancement of sorting, recycling and reusing discarded electrical
and electronic appliances. In order to finance the waste collection and processing, the government levies a recycling
contribution in some cases (included in the purchase price of this product).
Max. load
230V 50Hz*
10 A (40.000 x)
8 A (>40.000 x)
2,6 A / 600 VA
10 A / 2.300 VA
2,6 A / 600 W
4 A / 920 VA
PM005-34000R16063