Cleaning Mode Selection - Hyundai Homebot 3.0 Benutzerhandbuch

27
27. Dustbin box lock
28. Dustbin box cover
REMOTE CONTROL
1. ON/OFF & Cancell key
2. Speed selection (Normal/Slowly)
3. Forward button
4. Turn left button
5. Turn right button
6. Backward button
7. Mute button
8. Spot cleaning mode
9. Auto cleaning mode
10. Mopping mode
11. Auto - recharging button
3.1 QUICK USER GUIDE
1
1M
1M
2M
3
1. Position the charging base.
Install the charging base on the flat ground firmly and against the
vertical wall (fixed on the wall with the charging base sticker). Ensure
no obstacles or hollow areas 2M away from the charging base in front
and 1M on left and right.
2. Two charging methods
Connect the AC-DC adaptor with the charging hole on unit.
Control the unit return to the charging base under stand-by or working
mode. (Press the auto recharge button on remote controller or press
the charge button on unit.)
3. Auto recharge
Connected the charging station, the cleaner will auto return to
charging base when power lower than 20%.
Attention:
Please keep the charging base well connected with power socket,
otherwise, the cleaner cannot find charging station to perform auto
recharge.
29. HEPA filter
30. Primary filter
2
4.TURN ON THE UNIT
Long press the ON button for 3 seconds to turn on the unit, blue
flashing. Under stand-by mode, long press the ON button for 3
28
seconds after ON sound to turn off the unit.
3.2 CLEAN/PAUSE/RECHARGE/STAND-BY/TURN OFF
29
1. CLEAN
A. Long press the ON button to turn on the unit.
B. Short press the ON button on unit or press " Auto" button on Apps
or remote to start working.
30
2.PAUSE
Pause means to switch off the unit from clean mode to stand-by mode,
short press ON button, the unit paused working.
3.CHARGE
A. Press CHARGE button on Apps or on remote or press HOME button
on unit for charging.
B. When finish the cleaning task or battery power lower than 20%,
then unit will return to charging base for charging automatically.
4.STAND-BY
Press ON button on remote controller switch to stand-by mode, press
the ON button again to wake up the unit.
Attention
Under stand-by mode, press the ON on unit also can wake up it.
5.TURN OFF
1. Long press the ON button on unit for 3 seconds after "Di" sound to
turn off the unit.
2. Under stand-by mode, if the unit is idle for 5 minutes, it will be turn
off automatically.

3.3 CLEANING MODE SELECTION

1. AUTO MODE (SMART CLEAN)
Press" Auto" on remote or "Smart Clean" on Apps. After cleaning
task started, combined along with Gyro-Sensor + SLAM technology
to collect the room envrionment for analysis and calculate, Path
planned, step by step, orderly and efficiently to clean the floors in high
coverage. After finish the cleaning, the unit returnsback to origin or
docking station for charging.
Room A
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Room D -- next stepR
Attention:
The Robot plans path automatically when working, if being moved, it
will be rebuild the plan path and clean again. Please DO NOT move the
Robot randomly to ensure high efficiently cleaning. After cleaning task
started, the robot will stop a while to search in place and build clean
path, depends on the room's complexity.
2. SPOT CLEANING
Press "SPOT" button on remote controller, this mode is usually used
to clean floors where dirt is more concentrated. It will clean the area
within 1m2 and clean by spiral mode automatic operate in around 2-3
minutes.
Room B
oom C --- Cleaning