Inhaltsverzeichnis
Werbung
OBJ_BUCH-0000000025-001.book Page 16 Friday, February 25, 2011 9:30 AM
en
16
Character
Unit of measure,
international
kg
L
dB
pA
L
dB
wA
L
dB
pCpeak
K...
2
a
m/s
m, s, kg, A, mm, V,
W, Hz, N, °C, dB,
min, m/s
For your safety.
Read all safety warnings and all
WARNING
instructions. Failure to follow the
warnings and instructions may result in electric shock,
fire and/or serious injury.
Save all warnings and instructions for future reference.
Do not use this power tool before you have thor-
oughly read and completely understood this
Instruction Manual and the enclosed "General
Safety Instructions" (document number
3 41 30 054 06 1). The documents mentioned should be
kept for later use and enclosed with the power tool,
should it be passed on or sold.
Please also observe the relevant national industrial safety
regulations.
Intended use of the power tool:
for sanding small surfaces, corners and edges, for sawing
thin parts of steel sheet, wood and plastic, for scraping,
polishing, rasping, cutting and separating without water in
weather-protected environments, using the application
tools and accessories recommended by FEIN.
Special safety instructions.
Hold the power tool by the insulated gripping surfaces
when performing operations where the application tool
could contact hidden wires. Contact with a "live" wire
will also make exposed metal parts of the power tool
"live" and shock the operator.
Use clamps or another practical way to secure and sup-
port the workpiece to a stable platform. Holding the
work by hand or against your body leaves it unstable and
may lead to loss of control.
Grasp the power tool in such a safe manner that your
body never comes into contact with the application tool,
especially while working with application tools such as
saw blades or other blades pointed toward the grasping
range. Touching sharp tips or cutting edges can lead to
injuries.
Wear personal protective equipment. Depending on appli-
cation, use face shield, safety goggles or safety glasses.
As appropriate, wear dust mask, hearing protectors,
gloves and workshop apron capable of stopping small
abrasive or workpiece fragments. The eye protection
Unit of measure,
national
kg
dB
dB
dB
2
m/s
m, s, kg, A, mm, V,
W, Hz, N, °C, dB,
2
2
min, m/s
must be capable of stopping flying debris generated by
various operations. The dust mask or respirator must be
capable of filtrating particles generated by your opera-
tion. Prolonged exposure to high intensity noise may
cause hearing loss.
Do not direct the power tool against yourself, other per-
sons or animals. Danger of injury from sharp or hot
application tools.
Do not rivet or screw any name-plates or signs onto the
power tool. If the insulation is damaged, protection
against an electric shock will be ineffective. Adhesive
labels are recommended.
Clean the ventilation openings on the power tool at regu-
lar intervals using non-metal tools. The blower of the
motor draws dust into the housing. An excessive accu-
mulation of metallic dust can cause an electrical hazard.
Use and handling of the battery (battery pack)
To avoid hazardous situations such as burns, fire, explo-
sion, skin injuries, and other injuries when handling the
battery, observe the following instructions:
Batteries must not be disassembled, opened or reduced
in size. Do not subject batteries to mechanical impact or
shock. Hazardous vapours and fluid can escape in case of
damage and improper use of the battery. The vapours can
irritate the respiratory system. Liquid ejected from the
battery may cause skin irritations or burns.
When battery fluid from a damaged battery has come into
contact with objects close by, check the respective com-
ponents, clean them or replace them as required.
Keep the battery away from heat and fire. Do not store the
battery in direct sunlight.
Do not remove the battery from its original packaging
until it is going to be used.
Before any work on the machine itself, remove the bat-
tery from the power tool. If the power tool accidentally
starts, there is danger of injury.
Remove the battery only when the power tool is switched
off.
Keep the battery away from children.
Keep the battery clean and protect it against moisture
and water. Clean contaminated battery terminals and
power tool connections with a dry, clean cloth.
Explanation
Weight according to EPTA-Procedure 01/2003
Sound pressure level
Sound power level
Peak sound pressure level
Uncertainty
Vibrational emission value according to EN 60745
(vector sum of three directions)
Basic and derived units of measure from the inter-
national system of units SI.
Werbung
Inhaltsverzeichnis
