Black & Decker BHFEA640W Anleitung Seite 9

Read all of this manual carefully before
using the appliance
Keep hair away from brushes, openings
and other moving parts.
use charger S033GB3300100 for UK
use charger S033GV3300100 for EU
S010Q 23
S033G*3300100
Features
This tool includes some or all of the following features.
1. On/off power button
2. Hard floor speed button
3. Carpet speed button
4. Battery charge indicator
5. Main handle
6. Vacuum inlet
7. Charge port
8. Extension pole
9. Extension pole release button
10. Pre filter
11. Lift away dust canister
11a. Dust canister release button
11b. Dust canister door release button
12. Floor head
13. 2 in 1 accesory tool
14. Crevice tool
15. Pet head (Only available with BHFEA640WP unit)
16. Powered pet head (Only available with BHFEA640WP
unit)
17. Exhaust filter
18. Wall mounted charging and accesory storage station
19. Charger
20. On pole storage attachment
21. Soft beater bar (Only available with BHFEA640WP unit)
Warning! Suitable for hard floor only. DO NOT USE on
carpets or rugs.
Use
Charging the battery (Fig. A - C)
The supplied charger offers two possible ways to charge your
battery.
Unit charging
u
Unit wall mounted charging
u
Warning! Do not charge the battery at ambient temperatures
below 4 °C or above 40 °C. Follow all charging instructions
and do not charge the appliance outside of the temperature
range specified in the instructions. Charging improperly or at
temperatures outside of the specified range may damage the
battery and increase risk of fire.
(Original instructions)
Unit charging (Fig. A)
Locate the circular charge port (7) at the rear of the hand
u
held unit.
Align the circular magnetic contact (19) from the charger
u
onto the charge point of the unit (7)
Plug the charger into an appropriate electrical outlet
u
The blue LED (4) on the vaccum display will flash
u
indicating that the battery is being charged.
The blue LEDs (4) will illuminate in segments, displaying
u
the state of charge of the unit
The completion of charge is indicated by the bue LEDs (4)
u
turning off. The unit is fully charged and may be used at
this time or left on the charger.
Unit wall mounted charging (Fig B, C)
The product can be attached to a wall, to provide a convenient
accesory storage and charging point for the appliance.
When mounting to a wall, make sure the mounting method is
suitable for the wall type and is appropriate to the weight of
the appliance.
Note: Wall mounted dock comes withs the arms attached. The
side tool storage arms (18b) can be removed from the main
unit (18).
This is possible for the user to do if they don't have enough
space or only want to utilize one side arm. To remove storage
side arms from the charge dock, pull the arm firmly upwards.
To reconnect, align the arm with the locking holes and press
down.
Mark the location of the charging station screw holes on
u
the wall (at a height that allows the unit to hang without
hitting the floor and within reach of an electrical outlet for
charging the vacuum while it is on the charging station
(18).
Fix the charging station (18) to the wall using appropriate
u
screws and plugs for the type of wall, and weight of
the appliance.
Slide the magnetic charger (19) into the charging station
u
as shown in Figure B. Push the release button (18a) down
to align the slots on the magnetic charger head (19) with
the ribs on the charging station (18). Slide the magnetic
head down till the release button (18a) pushes back into
place. Ensure it is locked into place before proceeding..
Note: To remove the magnetic charger (19) from the charging
base press the release button (18a) on the charging station
and slide the magnetic charger up and away from the
charging station.
Plug the charger into an appropriate outlet.
u
Install the unit onto the charge point as shown in figure C.
u
Align the hook on the charging station into the slot at the
rear of the unit.
The blue LED (4) on the vaccum will flash indicating that
u
the battery is being charged.
ENGLISH
9