Inhaltsverzeichnis
Werbung
34
TCS Passive Series
TCS Passive Series
Illustrated here are the components parts available for TCS cabinets:
TCS62-SB (WH)
Swivel bracket for TCS62
Contents:
1 x Bracket
2 x M8 Bolts
2 x M10 Bolts
2 x M8 Spring Washers
2 x M10 Spring Washers
2 x M8 Flat Washers
2 x M10 Flat Washers
TCS122-FP (WH)
Fly Plate Kit for TCS122
Contents:
2 x Fly Plates
4 x M10 Bolts
4 x M10 Spring Washers
4 x M10 Flat Washers
TCS-FK1 (WH)
Inter-Cabinet Coupler Kit for TCS122 or TCS152
Contents:
2 x ICC
TCS-FK2 (WH)
Inter-Cabinet Coupler Kit for TCS122 or TCS152
Contents:
2 x ICC
TCS152-FP (WH)
Fly Plate Kit for TCS152
Contents:
2 x Fly Plates
4 x M10 Bolts
4 x M10 Spring Washers
4 x M10 Flat Washers
TCS115-FP (WH)
Fly Plate Kit for TCS115B
Contents:
2 x Fly Plates
4 x M10 Bolts
4 x M10 Spring Washers
4 x M10 Flat Washers
TCS-FK3 (WH)
Inter-Cabinet Coupler Kit for TCS115B
Contents:
2 x ICC
EB-10-40
Eyebolt M10 x 40mm
Contents:
1 x Eyebolt
Suspending with
TCS cabinets can be suspended using optional eyebolts coupled to the internal rigging points provided on the
(EN)
top, bottom and sides and back. The simplest method is to use the two rigging points on the top and a single
Eyebolts
pull-back rigging point in the centre of the rear panel.
Remove the appropriate countersunk screws and replace them withshoulder eyebolts, which must have a
thread length of at least 18 mm. Use the rear rigging point to angle the cabinet for optimum room coverage.
Cabinets may be hung upside down if required.
IMPORTANT NOTE FOR ALL INSTALLATION METHODS: The mounting of a permanently installed sound
system may be dangerous unless undertaken by qualified personnel with the required experience and
certification to perform the necessary tasks. Walls, floors or ceilings must be capable of safely and securely
supporting the actual load. The mounting accessory used must be safely and securely fixed both to the
loudspeaker and to the wall, floor or ceiling.
When mounting rigging components on walls, floors or ceilings, ensure that all fixings and fasteners used
are of an appropriate size and load rating. Wall and ceiling claddings, and the construction and composition
of walls and ceilings, all need to be taken into account when determining whether a particular fixing
arrangement can be safely employed for a particular load. Cavity plugs or other specialist fixings, if required,
must be of an appropriate type, and must be fitted and used in accordance with the maker's instructions.
The operation of your speaker cabinet as part of a flown system, if installed incorrectly and improperly,
can potentially expose persons to serious health risks and even death. In addition, please ensure that
electrical, mechanical and acoustic considerations are discussed with qualified and certified (by local state or
national authorities) personnel prior to any installation or flying.
Make sure that speaker cabinets are set up and flown by qualified and certified personnel only,
using dedicated equipment and original parts and components delivered with the unit. If any parts or
components are missing please contact your Dealer before attempting to set up the system.
Be sure to observe the local, state and other safety regulations applicable in your country. Music Tribe,
including the Music Tribe companies listed on the enclosed "Service Information Sheet", assumes no liability
for any damage or personal injury resulting from improper use, installation or operation of the product.
Regular checks must be conducted by qualified personnel to ensure that the system remains in a secure
and stable condition. Make sure that, where the speaker is flown, the area underneath the speaker is free of
human traffic. Do not fly the speaker in areas that can be entered or used by members of the public.
Speakers create a magnetic field, even if not in operation. Therefore, please keep all materials that can be
affected by such fields (discs, computers, monitors, etc)
at a safe distance. A safe distance is usually between 1 and 2 metres.
35
Quick Start Guide
Werbung
Inhaltsverzeichnis
