HIKMICRO M Serie Kurzanleitung Seite 7

exposure limits set forth for an uncontrolled
environment.
ce matériel est conforme aux limites de dose d'exposition
aux rayonnements, CNR-102 énoncée dans un autre
environnement.
For M11, M11W, M20, M20W and M30, please pay
attention to the following notes when the device is
operating in 5 GHz:
(i) The device for operation in the band 5150-5250 MHz is
only for indoor use to reduce the potential for harmful
interference to co-channel mobile satellite systems;
(ii) The maximum antenna gain permitted for devices in
the bands 5250-5350 MHz and 5470-5725 MHz shall
comply with the e.i.r.p. limit; and
(iii) The maximum antenna gain permitted for devices in
the band 5725-5825 MHz shall comply with the e.i.r.p.
limits specified for point-to-point and non point-to-point
operation as appropriate.
Pour les modèles M11, M11W, M20, M20W et M30,
veuillez prêter attention aux remarques suivantes lorsque
l'appareil fonctionne en 5 GHz :
(i)Les dispositifs fonctionnant dans la bande
5150-5250 MHz sont réservés uniquement pour une
utilisation à l'intérieur afin de réduire les risques de
brouillage préjudiciable aux systèmes de satellites
mobiles utilisant les mêmes canaux.
(ii) Le gain d'antenne maximal autorisé pour les appareils
dans les bandes 5250-5350 MHz et 5470-5725 MHz
doivent respecter le pire limiter; et
(iii) Le gain d'antenne maximal autorisé pour les appareils
dans la bande 5725-5825 MHz doivent respecter le pire
limites spécifiées pour le point-à-point et l'exploitation
non point à point, le cas échéant.
Users should also be advised that high-power radars are
allocated as primary users (i.e. priority users) of the
bands 5250-5350 MHz and 5650-5850 MHz and that
these radars could cause interference and/or damage to
LE-LAN devices.
Les utilisateurs de radars de haute puissance sont
désignés utilisateurs principaux (c.-à-d., qu'ils ont la
priorité) pour les bandes 5250-5350 MHz et
5650-5850 MHz et que ces radars pourraient causer du
brouillage et/ou des dommages aux dispositifs LAN-EL.
Safety Instruction
Please read all the safety information carefully before
using.
These instructions are intended to ensure that user can
use the product correctly to avoid danger or property loss.
Laws and Regulations
● Use of the product must be in strict compliance with
the local electrical safety regulations.
Transportation
● Keep the device in original or similar packaging while
transporting it.
● Keep all wrappers after unpacking them for future use.
In case of any failure occurred, you need to return the
device to the factory with the original wrapper.
Transportation without the original wrapper may result
in damage on the device and the company shall not
take any responsibilities.
● Do not drop the product or subject it to physical shock.
Keep the device away from magnetic interference.
Power Supply
● The input voltage should meet the limited energy
circuit (5 VDC, 2 A) according to the IEC61010-1
standard. Please refer to technical specifications for
detailed information.
● Make sure the plug is properly connected to the power
socket.
● DO NOT connect multiple devices to one power adapter,
to avoid over-heating or fire hazards caused by
overload.
● For the device without a supplied power adapter, use
the power adapter provided by a qualified
manufacturer. Refer to the product specification for
detailed power requirements.
Battery
● Improper use or replacement of the battery may result
in explosion hazard. Replace with the same or
equivalent type only. The battery type is
E97-13-1S1P26650. Dispose of used batteries in
conformance with the instructions provided by the
battery manufacturer.
● Do not charge other battery types with the supplied
charger. Confirm there is no flammable material within
2 m of the charger during charging.
● For long-term storage of the battery, make sure it is
fully charged every half year to ensure the battery
quality. Otherwise, damage may occur.
● DO NOT place the battery near heating or fire source.
Avoid direct sunlight.
● DO NOT swallow the battery to avoid chemical burns.
● DO NOT place the battery in the reach of children.
● CAUTION: Risk of explosion if the battery is replaced by
an incorrect type.
● Do not dispose of the battery into fire or a hot oven, or
mechanically crush or cut the battery, which may result
in an explosion.
● Do not subject the battery to extremely low air
pressure, which may result in an explosion or the
leakage of flammable liquid or gas.
● When the device is powered off and the RTC battery is
full, the time settings can be kept for 2 months.
● In the first use, power on the device and charge the RTC
battery with the lithium battery for more than 8 hours.
● The battery voltage is 3.7 V, and the battery capacity is
5000 mAh.
● The battery is certified by UL2054.
Maintenance
● If the product does not work properly, please contact
your dealer or the nearest service center. We shall not
assume any responsibility for problems caused by
unauthorized repair or maintenance.
● Wipe the device gently with a clean cloth and a small
quantity of ethanol, if necessary.
● If the device is used in a manner not specified by the
manufacturer, the protection provided by the device
may be impaired.
● Please notice that the current limit of USB 3.0
PowerShare port may vary with the PC brand, which is
likely to result in incompatibility issue. Therefore, it's
advised to use regular USB 3.0 or USB 2.0 port if the
USB device fails to be recognized by PC via USB 3.0
PowerShare port.
● Your camera will periodically perform a self-calibration
to optimize image quality and measurement accuracy.
In this process the image will pause briefly and you will
hear a "click" as a shutter moves in front of the
detector. The self-calibration will be more frequent
during the startup or in very cold or hot environments.
This is a normal part of operation to ensure optimum
performance for your camera.
5