Noise/Vibration Information - Bosch GSC 10,8 V-LI Professional Originalbetriebsanleitung

OBJ_BUCH-840-006.book Page 11 Friday, May 23, 2014 12:04 PM
10 Upper cutter
11 Bottom cutter
12 Adjustment screw, bottom cutter
13 Fastening screw for bottom cutter
14 Setting gauge*
*Accessories shown or described are not part of the standard de-
livery scope of the product. A complete overview of accessories
can be found in our accessories program.
Technical Data
Cordless Sheet Metal Shear
Article number
Rated voltage
Stroke rate at no load n
0
Max. steel sheet cutting capacity
Smallest curve radius
Weight according to
EPTA-Procedure 01/2003
Permitted ambient temperature
– during charging
– during operation* and during
storage
Recommended batteries
Recommended chargers
# 2
to 400 N/mm with reference to steel sheet
* Limited performance at temperatures <0 °C

Noise/Vibration Information

Sound emission values determined according to EN 60745.
Typically the A-weighted sound pressure level of the product
is less than 70 dB(A). Uncertainty K < 1.5 dB.
The noise level when working can exceed 80 dB(A).
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 60745:
2 2
a = 3.5 m/s , K< 1.5 m/s .
h
The vibration level given in this information sheet has been
measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with anoth-
er. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or insertion tools or is
poorly maintained, the vibration emission may differ. This
may significantly increase the exposure level over the total
working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may signif-
icantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work pat-
terns.
Bosch Power Tools
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under "Technical Data" is in conformity with all rele-
vant provisions of the directives 2011/65/EU, 2014/30/EU,
2006/42/EC including their amendments and complies with
the following standards: EN 60745-1, EN 60745-2-8.
Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ETM9,
70764 Leinfelden-Echterdingen, GERMANY
Henk Becker
Executive Vice President
GSC 10,8 V-LI
Engineering
3 601 J26 1..
V= 10.8
-1
min 3600
#
mm 1.3
Robert Bosch GmbH, Power Tools Division
mm 15
70764 Leinfelden-Echterdingen, GERMANY
Leinfelden, 28.04.2014
kg 1.4
Assembly
Battery Charging
°C 0...+45
 Use only the chargers listed in the technical data. Only
°C –20...+50
GBA 10,8V...
Note: The battery supplied is partially charged. To ensure full
AL 11..
capacity of the battery, completely charge the battery in the
battery charger before using your power tool for the first time.
The lithium-ion battery can be charged at any time without re-
ducing its service life. Interrupting the charging procedure
does not damage the battery.
Battery Charge-control Indication
The three green LEDs of the battery charge-control indicator
4 indicate the charge condition of the battery 2. For safety
reasons, it is only possible to check the status of the charge
condition when the machine is at a standstill.
– To indicate the charge condition, press and hold button 3
LED
Continuous lighting 3 x green
Continuous lighting 2 x green
Continuous lighting 1 x green
Flashing light 1 x green
Removing the battery
– To remove the battery 2, press the unlocking buttons 1
Operation
Starting Operation
Inserting the battery
 Use only original Bosch lithium-ion batteries with the
Helmut Heinzelmann
Head of Product Certification
PT/ETM9
these chargers are matched to the lithium-ion battery of
your power tool.
of the switched off machine.
and pull the battery out of the machine to the rear. Do not
exert any force.
voltage listed on the nameplate of your power tool. Using
other batteries can lead to injuries and pose a fire hazard.
English | 11
Capacity
2/3
1/3
<1/3
Reserve
1 609 92A 0NT | (23.5.14)