Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Sport-flyer for 500-600W brushless motor or .20-.25 glow engine
SPECIFICATION
Wingspan:
Length:
All-up Weight:
RECOMMENDER POWER SYSTEM & RC EQUIPMENT
Motor/Engine
Propeller
ESC
Fuel Tank
Battery
Ailerons
Servos
Elevator & Rudder
Throttle
*) 100-150 ml fuel tanks are good for regular .20-.25 engines, more powerful and "thirstier" O.S. MAX-25FX II will be happier with 150-170 ml tank.
Recommended Glues
Unless stated otherwise, use medium cyanoacrylate (CA) glue (KAV9952
KAVAN CA Medium). D-box sheeting and wing ribs are better to be glued
using a water resistant white aliphatic resin, like our KAV9960 KAVAN White
Glue (alternatively, you can use this sort of glue for most of wood-to-wood
RECOMMENDED COVERING MATERIAL
The iron-on films like ORACOVER® or ORALITE® (if you wanted to keep the
weight really down) will work the best for your FunStik.
Tools and Accessories
• Very sharp modeller's knife (e.g. Excel 16001 with No. 11 blades)
• Scissors
• Electric drill with drill bits
• Wire cutter
• Long nose pliers
• Screwdrivers
• Razor saw
• Sandpaper No. 80, 100, 180, 360-400
• Needle files
• Soldering iron and solder
• Clothing pegs
MODEL ASSEMBLY
Wing
1. Locate all the parts for one half of the wing; sand to fit all plywood/liteply
parts, the inner leading edge, bottom and upper main spars 14 if necessary.
2. One by one, insert all the wing ribs 1 to 4 into the liteply main spar shear
webbing 15.
3. Insert the inner leading edge, bottom and upper main spars 14 and the
trailing edge shear webbing 16 into respective notches in ribs.
4. Once you are satisfied with the fit and you are sure the wing structure is
FunStik Kit
Designed and manufactured in the Czech Republic
1280 mm
1040 mm
1450-1500 g
Electric
KAVAN C3542-1200
APC 10x6E
KAVAN R-50SB
-
KAVAN LiPo 11.1 V 2200 mAh 40/80C
2x GO-13MG
2x GO-52MG (2x GO-17MG)
-
3
Wing Section:
Controls:
joints). The highly loaded parts (wing roots, wing main spars, firewall etc.)
should be glued together using 30 minute (or slower) epoxy (like KAV9967
Epoxy 30min) offering high strength and enough time for the correct posi-
tioning/alignment.
• Modeller's pins
• Epoxy mixing stick and vessel
• Masking tape, clear sticky tape
• Rubbing alcohol (for cleaning up excessive epoxy)
• Paper tissue or soft cloth (for cleaning up excessive epoxy)
• Straightedge with scale
• Square edge
• Thin clear plastic film (for protecting the building plan)
• Permanent marker
• Modeller's sealing iron, heat gun (for covering)
• Lightweight balsa filler
true and straight, glue all the parts together. We recommend using epoxy
for the root ribs 1-3 and the main spars 14.
5. Epoxy the wing bolt reinforcements 10 and 11 in place.
6. Use white aliphatic resin to glue the top and bottom D-box balsa sheeting
19 and the top and bottom trailing edge sheeting 20. Be sure the wing
still remains true and straight.
7. Glue the wing centre bottom balsa sheeting 8 and 9 and the top sheeting
9 in place.
symmetrical
Aileron, rudder, elevator, throttle
Glow Engine
O.S. MAX-25FX II
9x5-6"
-
100-170 ml*
KAVAN NiMH 4.8 V 2000 mAh
2x GO-13MG
2x GO-52MG
GO-06MG
Werbung
