Operating Elements And Connections; Safety Notes - Monacor AV-100BS Bedienungsanleitung

Please unfold page 5. Then you can always see the
operating elements and connections described.

1 Operating Elements and Connections

1 Volume control
2 Indicating LEDs for the four camera channels:
C1 = reception channel 1
C2 = reception channel 5
C3 = reception channel 3
C4 = cable-connected camera, connected to the
jack C4 (16)
3 DIP switch on the lower side of the unit for defining
the number of the cameras used (see chapter 4.2)
4 Button SKIP for manual selection of the camera
channels
5 Button for adjusting the operating mode
button not pressed ("AUTO"):
automatic camera selection
button pressed ("MANUAL"):
manual camera selection via the button SKIP (4)
6 POWER switch
7 Control TIME for adjusting the dwell time (2 – 60 s)
for a camera picture in the automatic selection
mode
8 Reception antenna (must not be broken off or
scratched)
9 Audio input (white phono jack) and video input
(yellow phono jack) for video recorder replay:
connection to the audio and video output of a
recorder
10 Audio output (white phono jack) and video output
(yellow phono jack) for video recorder replay or for
connecting a second monitor: connection to the
audio and video input of a recorder or a second
monitor
11 Selector switch for the signal source
CAMERA: The monitor is set to replay of the
camera signals.
VCR: The monitor is set to video recorder
replay.
12 Control V-HOLD for vertical synchronization
13 Brightness control BRT.
14 Contrast control CONT.
15 Low voltage jack DC IN for connecting the sup-
plied power supply unit
16 Connection jack C4 for operating a cable-connect-
ed camera, e. g. MONACOR TVCCD-510

2 Safety Notes

The units (monitor and power supply unit) correspond
to the directive for electromagnetic compatibility
89/336/EEC. The power supply unit also corre-
sponds to the low voltage directive 73/23/EEC.
Attention! The power supply unit and the moni-
tor are supplied with very high voltage
dangerous to life. Leave servicing to
skilled personnel only. Inexpert handling
may cause an electric shock hazard. Fur-
thermore, any guarantee claim will expire
if any of the units has been opened.
Please observe the following items in any case:
Caution! The picture tube of the monitor is vacuous.
In case of mechanical damage, there is an implo-
sion hazard and scattered glass may cause injuries.
The units are suitable for indoor use only. Protect
them against dripping water and splash water, high
air humidity, and extreme temperatures (admissible
ambient temperature range -10 °C to +55 °C).
Do not place any vessel filled with liquid on the unit,
e. g. a drinking glass.
The heat generated within the units must be carried
off by air circulation. Therefore, never cover the air
vents.
Do not insert anything into the air vents! This may
result in an electric shock or in damage to the unit.
Do not operate the monitor or immediately dis-
connect the power supply unit from the mains socket
1. if there is visible damage to the monitor, the
power supply unit, or the mains cable,
2. if a defect might have occurred after a unit was
dropped or suffered a similar accident,
3. if malfunctions occur.
In any case the units must be repaired by skilled
personnel.
A damaged mains cable of the power supply unit
must be replaced by the manufacturer or author-
ized skilled personnel only.
Never pull the mains cable when disconnecting the
mains plug from the socket, always seize the plug!
For cleaning only use a dry, soft cloth; never use
chemicals or water.
No liability for any damage will be accepted if the
units are used for other purposes than originally
intended, if they are not correctly connected or
operated or not repaired in an expert way.
If the units are to be put out of operation definitively,
take them to a local recycling plant for a disposal
which is not harmful to the environment.
Important for U.K. Customers!
The wires in this mains lead are coloured in accord-
ance with the following code:
blue = neutral, brown = live
As the colours of the wires in the mains lead of this
appliance may not correspond with the coloured
markings identifying the terminals in your plug, pro-
ceed as follows:
1. The wire which is coloured blue must be con-
nected to the terminal in the plug which is
marked with the letter N or coloured black.
2. The wire which is coloured brown must be con-
nected to the terminal which is marked with the
letter L or coloured red.
9