Cleaning, Maintenance And Ordering Of Spare Parts; Cleaning The Equipment - EINHELL BRILLIANTO Originalbetriebsanleitung

5.2 Charging the Li battery pack (Fig. 5-6)
1. Remove the battery pack (a) from the handle,
pressing the pushlock button (b) downwards
as you do so.
2. Check that your mains voltage is the same as
that marked on the rating plate of the battery
charger. Insert the power plug of the charger
(c) into the socket outlet. The green LED will
then begin to blink.
3. Push the battery (a) onto the charger (c).
4. In the section entitled „Charger indicator" you
will fi nd a table with explanations of the LED
display on the charger.
The battery pack can become a little warm during
the charging. This is normal.
If the battery pack fails to charge, check:
•
whether there is voltage at the socket outlet
•
whether there is good contact at the charging
contacts
If the battery pack still fails to charge, send
•
the charging unit
•
and the battery pack
to our customer service center.
To ensure that items are properly packaged
and delivered when you send them to us,
please contact our customer service or the
point of sale at which the equipment was
purchased.
When shipping or disposing of batteries and
cordless tools, always ensure that they are
packed individually in plastic bags to prevent
short circuits and fi res.
To ensure that the battery pack provides long ser-
vice, you should take care to recharge it promptly.
You must recharge the battery pack when you
notice that the performance of the device drops.
Never allow the battery pack to become fully di-
scharged. This will cause it to develop a defect.
5.3 Battery capacity indicator (Fig. 6/Item d)
Press the button for the battery capacity indicator
(e). The battery capacity indicator (d) shows the
charge status of the battery using 3 LEDs.
All 3 LEDs are lit:
The battery is fully charged.
2 or 1 LED(s) are lit:
The battery has an adequate remaining charge.
Anl_BRILLIANTO_SPK13.indb 19 Anl_BRILLIANTO_SPK13.indb 19
GB
1 LED fl ashes:
The battery is empty, recharge the battery.
All LEDs blink:
The battery temperature is too low. Remove the
battery from the equipment, keep it at room tem-
perature for one day. If the fault reoccurs, this me-
ans that the rechargeable battery has undergone
exhaustive discharge and is defective. Remove
the battery from the equipment. Never use or
charge a defective battery.
6. Operation
On/Off switch (Fig. 1/Item 8)
Operation is performed as shown in Fig. 7. Obser-
ve the level of contents in the water tank. The level
is not allowed to be higher than the max. mark
(Fig. 4b). To read the level correctly, fi t the battery
and then place the equipment upright on the fl oor
(Fig. 1). To empty, remove the water tank and pour
out the contents (Fig. 4c/4d).
Note: An overfi lled water tank (water level or foam
above the Max. mark on the tank) will result in wa-
ter escaping at the ventilator housing. This will not
damage the equipment – remove the battery and
allow the equipment to dry.
Warning
If cleaning agent gets into contact with your skin
or into your eye, rinse immediately with lots of
clean water. Then consult a doctor or follow the
steps described on the safety data sheet or provi-
ded by the manufacturer of the cleaning agent.
7. Cleaning, maintenance and
ordering of spare parts
Hazard!
Always pull out the battery pack before starting
any cleaning work.

7.1 Cleaning the equipment

•
Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible.
•
We recommend cleaning the equipment im-
mediately each time after use.
•
Rinse the water tank with clear water after
use.
- 19 -
12.04.2023 09:47:51 12.04.2023 09:47:51