Before Starting The Equipment - EINHELL TC-BG 150 B Originalbetriebsanleitung

The stated noise emission values were measured
in accordance with a set of standardized criteria
and can be used to compare one power tool with
another.
The stated noise emission values can also be
used to make an initial assessment of exposure.
Warning:
The noise emission levels may vary from the level
specifi ed during actual use, depending on the
way in which the power tool is used, especially
the type of workpiece it is used for.
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
Limit the operating time!
All stages of the operating cycle must be conside-
red (for example, times in which the electric tools
are switched off and times in which the tool is
switched on but operates without load).
Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.
3. Health damage caused by hand-arm vib-
rations if the equipment is used over a pro-
longed period or is not properly guided and
maintained.

5. Before starting the equipment

Before you connect the equipment to the mains
supply make sure that the data on the rating plate
are identical to the mains data.
Anl_TC_BG_150_B_SPK13.indb 19 Anl_TC_BG_150_B_SPK13.indb 19
GB
Warning!
Always pull the power plug before making
adjustments to the equipment.
Pull the power plug before doing any mainte-
nance or assembly work on the equipment.
•
The equipment has to be set up where it can
stand securely.
•
Before starting work, firmly screw the grin-
ding/sanding machine to the workbench or
equivalent using the 4 mounting holes (8) in
the base plate (9).
•
All covers and safety devices have to be pro-
perly fitted before the equipment is switched
on.
•
It must be possible for the grinding/sanding
wheel to run freely.
•
Check that the voltage on the rating plate is
the same as your supply voltage before you
connect the equipment to the power supply.
5.1 Fitting the spark defl ector / safety window
(Fig. 3/4)
•
Fit the spark deflector for the grinding wheel
(3) as well as the spark deflector for the brus-
hing wheel (4) on the machine (Fig. 3).
•
Do this with the socket head screws (11), the
washers (12), the spring washers (13) and
the nuts (14).
•
Tighten the screw connection using a 4 mm
hex key and an 8 mm wrench. Important! Not
supplied.
5.2 Adjusting the spark defl ectors (Fig. 5/6)
•
The spark deflectors (3/4) have slots so that
you can adjust them in vertical direction.
•
To do so, slacken the socket head screws
(11) and push the spark deflector as close as
possible to the grinding wheel (5) / brushing
wheel (6).
•
Warning! The distance between the grinding
wheel/brushing wheel and the spark deflec-
tors must be set as small as possible; under
no circumstances should it exceed 2 mm at
the grinding wheel and 8 mm at the brushing
wheel.
•
Then secure the spark deflectors (3/4) again.
•
Warning! Adjust the spark deflectors (3/4)
periodically to compensate for wear on the
grinding wheel/brushing wheel.
- 19 -
17.11.2022 14:36:44 17.11.2022 14:36:44