Before Operation; Cleaning The Tool - Kress KG560E.9 Bedienungsanleitung

declared value depending on the ways in which the tool
is used dependant on the following examples and other
variations on how the tool is used:
How the tool is used
The tool being in good condition and well maintained
Using the correct accessory for the tool and ensuring it
is sharp and in good condition.
The tightness of the grip on the handles and if any anti
vibration accessories are used.
And the tool is being used as intended by its design
and these instructions.
This tool may cause hand-arm vibration
syndrome if its use is not adequately
managed.
WARNING: To be accurate, an estimation of
exposure level in the actual conditions of use
should also take account of all parts of the operating
cycle such as the times when the tool is switched off
and when it is running idle but not actually doing the
job. This may significantly reduce the exposure level
over the total working period.
Helping to minimise your vibration exposure risk.
Maintain this tool in accordance with these instructions
and keep well lubricated (where appropriate)
If the tool is to be used regularly then invest in anti
vibration accessories.
Plan your work schedule to spread any high vibration
tool use across a number of days.
INTENDED USE
The blower is intended for residential use only. Use the
blower outdoors to move yard debris as needed.

BEFORE OPERATION

ASSEMBLING & DISASSEMBLING THE
BLOWER TUBE
To Assemble (Fig. A)
- Align the groove and push the tube onto the
blower housing until you hear a "click".
To Disassemble (Fig. B)
- Press the tube-release button and pull the tube
out.
INSTALLING & REMOVING THE BATTERY
PACK
To Install (Fig. C)
- After recharging, insert the battery pack into tool's
battery port. A simple push and slight pressure
will be sufficient.
To Remove (Fig. D)
- Press the battery release button to release battery
pack from your tool.
OPERATION
AIR SPEED MODE (FIG.E)
NOTE: The blower is in the air speed mode as
packed in the box.
- Air speed mode is recommended for cleaning on
grass, as shown in Fig. G1.
AIR VOLUME MODE (FIG.F1, F2)
- Depress the nozzle release button and slide
forward for air volume mode.
- Air volume mode is recommended for cleaning on
hard ground such as cement, as shown in Fig.G2.
NOTE: To change modes, slide backward for air
speed mode.
To start
Variable Speed Dial control (Fig. G1, G2)
Turn the Variable Speed Dial clockwise or
anticlockwise to increase or decrease the blowing
speed / air volume with 3-speed switch.
NOTE: When Variable Speed Dial is in "O"
position, the blower cannot be started. Turn
the Variable Speed Dial to the desired speed
selection which will start the blower.
To stop (Fig. G3)
Turn the Variable Speed Dial clockwise to
"O"or depress the Trigger and release it to
have a quick stop. Turn the Variable Speed
Dial clockwise to "O" position after each use.
NOTE: After completing the quick stop,
Variable Speed Dial will not work until you have
the throttle trigger fully depressed.
USER TIPS
- Hold the blower tube approximately 8'' above the
ground when operating the tool.
Use a sweeping motion from side to side. Advance
slowly keeping the accumulated debris/leaves in
front of you.
- After blowing the debris/leaves into a pile, it is
easy to dispose of the pile.
CAUTION!
- Do not blow hard objects such as nails, bolts, or
rocks.
- Do not operate the blower near bystanders or
pets.
- Use extra care when cleaning debris from stairs or
other tight areas.
- Wear safety goggles or other suitable eye
protection, long pants, and shoes.
TURBO BUTTON FOR POWER BOOSTING (FIG.
H)
- Press the turbo button for power boosting while
working to temporarily increase the air flow to the
maximum level
- Release the Turbo button, the blower will return to
the previously selected speed.
NOTE: Turbo button for power boosting can increase
air flow significantly, and it can be used for clearing
heavy or wet debris.

CLEANING THE TOOL

Clean the tool regularly.
WARNING! Keep your product dry. Under
no circumstances spray with water.
- To clean the tool, use only mild soap and a damp
cloth.
- Do not use any type of detergent, cleaner or
solvent which may contain chemicals that could
seriously damage the plastic.
- Self lubricating bearings are used in your product,
therefore lubrication is not required.
11 11
EN