Technical Specifications - AER Cubello Bedienungsanleitung

6. Technical specifications

Instrument Instrument / line input, high impedance,
unbalanced
Connector:
Nom. input voltage:
Min. input voltage:
Max. input voltage:
Input impedance:
Signal / noise ratio (A-weighted):
Equivalent input noise voltage (A-weighted):
microphone Microphone input, XLR (balanced), stereo jack
(balanced), or mono jack (unbalanced)
Connector:
1 /sleeve = ground,
2 / tip = positive (+),
3 / ring = negative (–)
Nom. input voltage:
Min. input voltage:
Max. input voltage:
Nom. source impedance:
Input impedance (balanced):
Input impedance (unbalanced):
Voice filter (referred to 10 kHz): –10 dB at 270 Hz
Signal / noise ratio (A-weighted):
Equivalent input noise voltage
(A-weighted):
Phantom power (XLR only):
Supply resistors:
Load current:
aux in
Auxiliary input, e.g. for CD
Connector:
Nom. input voltage:
Min. input voltage,
using stereo jack plug:
using mono jack plug:
Max. input voltage:
Input impedance:
bluetooth Wireless audio input
Bluetooth version:
Frequency range:
Min. audio input level:
Signal / noise ratio (A-weighted):
line out Preamplifier output post master, tone controls,
aux in, bluetooth in, and effects
Connector:
Nom. output voltage:
Output impedance:
Min. load impedance:
Residual noise (A-weighted):
headphones Headphones output
Connector:
Nom. open loop output voltage:
Output impedance:
Output power with headphones
impedance 32...600 Ω
Residual noise (A-weighted), referred to
rated output power:
When plugged in, the speaker is muted.
12
¼" (6.35 mm) mono jack
100 mV (–20 dBV)
22 mV (–33 dBV)
6 V (+15 dBV)
2.2 MΩ 300 pF
3 μV (–110 dBV)
combo XLR / ¼" (6.35 mm) jack
10 mV (–40 dBV)
4 mV (–48 dBV)
1 V (0 dBV)
1 μV (–120 dBV)
48 VDC
max. 10 mA
3.5 mm stereo jack
500 mV(–6 dBV)
100 mV (–20 dBV)
200 mV (–14 dBV)
2 V (+6 dBV)
V 5.1 Bluetooth low energy radio
2.402–2.480 GHz
–6 dB FS
¼" (6.35 mm) mono jack
1 V (0 dBV)
5 μV (–106 dBV)
¼" (6.35 mm) stereo jack
min. 10 mW
–110 dB
bass
treble
internal efx
effects pan
91 dB
Power amp
Construction Monolithic, Class D, BTL mode
Rating
Distortion
Noise
Signal
200 Ω
processing
1.2 kΩ
2.7 kΩ
Limiter
Speaker
80 dB
system
Power supply Mains voltage:
6.8 kΩ
Mains fuse
Operating
temperature
Cabinet
Finish
Dimensions Height
22 kΩ
Weight
91 dB
100 Ω
2 kΩ
3 V
120 Ω
at 100 Hz
at 10 kHz
Digital effect processor
Modes:
Blends effect between instrument channel and
microphone channel.
Output power (THD= 1%)
Continuous output power is determined by the
limiter threshold, see below
THD + N (8 W / 4 Ω)
Measured at loudspeaker terminals
Residual noise (A-weighted), referred to
rated output power:
Acoustical:
Equalizer, subsonic filter, peak limiter,
power limiter
Threshold
8" (200 mm) dual cone full-range speaker
sealed enclosure
Power consumption:
Size
Rating
Permissible ambient temperature
Medium density fiber board,
thickness:
Water-based acrylic, black spatter finish
Width
Depth
Weight (without cover)
±8 dB
±11 dB
Reverb or delay
80 W / 4 Ω
< 0.1%
–98 dB
approx. 13 dB (A) / 1 m
40 W / 4 Ω
100–240 V~, 50–60 Hz
max. 100 W
5 x 20 mm
T 2.5A L 250 V
0...35 °C
16 mm (0.47")
299 mm (11.77")
294 mm (11.57")
297 mm (11.69")
7.2 kg (15.9 lbs)