Maintenance; Operation - Silverline Rotary Laser Level Kit Handbuch

GB
Checking vertical rotational level:
1. Position the unit on its tripod on the floor approximately 15m from the
base of the wall. The right side of the unit should face the wall. Level
the unit by adjusting the Y Axis Levelling Screw (7)
2. Mark a point A on the lower part of the wall. Turn the power on and
manually direct the laser beam to point A
3. Turn the rotary head so the laser beam moves approximately 4.5m
upwards on the wall. Mark as point B
4. Rotate the unit 180˚ so the left side of the unit faces the wall. Re-level
the unit by adjusting the Y axis levelling screw. Manually direct the
laser beam to point A
5. Turn the rotary head so that the laser beam is at the same height
as point B. Mark as point C. No adjustments are necessary if the
difference between points B and C is 2mm or less
Correcting vertical rotational level:
1. Adjust the Y Axis Levelling Screw (7) so laser beam is midway between
points B and C. (This will cause the bubble in the Y Vial (4) to shift
from the centre)
2. Centre the Y vial bubble by adjusting the Y vial calibration screw
(adjacent to the vial) with Screwdriver (11) supplied
3. Re-check the accuracy of the laser by repeating the calibration
process as necessary
Alternative Calibration Method
1. Using a spirit level, mark a straight horizontal line on the wall at the
height required for your project
Checking the X-axis vial:
1. Position the Laser Level approximately 10m away from the wall,
ensuring that the X Axis Vial (10) is facing the wall
2. Turn the power on so that the Rotary Head spins to create a line on
the wall
3. Adjust the X Axis Levelling Screw (6) until the laser line matches the
line you have drawn on the wall
4. If the bubble is not in the centre of the X Axis Vial (10), use the
Screwdriver supplied (11) to adjust the vial until the bubble is centred
Checking the Y-axis vial:
1. Turn the unit through 90° so that the Y Axis Vial (4) is facing the wall
2. Repeat procedure as above, adjusting the Y Axis Levelling Screw (7)

Operation

Levelling
• Set up your rotary laser level in accordance with guidance in in 'Before
Use' section
• Ensure that the rotary laser is level by checking the vials and adjusting
the levelling screws. See Calibrating the Laser Level' for guidance
• Turn power on and use the control button to establish the correct speed.
• Mark the desired positions
Plumbing
• Set up your rotary laser level in accordance with guidance in 'Before
Use' section
• Ensure that the rotary laser is level by adjusting the Y levelling screw (7)
until the plumbers vial bubble is centred
• Turn power on and use the control button to establish the correct speed
• Mark the desired positions
• It is also possible to operate the unit manually: switch on the unit and
turn the unit by hand until the laser beam is aligned with your target
Accessories
A full range building accessories is available from your Silverline stockist
6

Maintenance

Cleaning
WARNING: ALWAYS wear protective equipment including eye protection and
gloves when cleaning this tool.
• Keep your tool clean at all times. Dirt and dust will cause internal parts to
wear quickly, and shorten the device's service life
• Clean the body of your machine with a soft brush, or dry cloth
• Never use caustic agents to clean plastic parts. If dry cleaning is not
sufficient, a mild detergent on a damp cloth is recommended
• Water must never come into contact with the tool
• Ensure the tool is thoroughly dry before using it
• If available, use clean, dry, compressed air to blow through the ventilation
holes (where applicable)
Storage
• Store this tool carefully in a secure, dry place out of the reach of children
Disposal
Always adhere to national regulations when disposing of power tools that
are no longer functional and are not viable for repair.
• Do not dispose of power tools, batteries or other waste electrical and
electronic equipment (WEEE), with household waste
• Contact your local waste disposal authority for information on the correct
way to dispose of power tools