Makita HR001G Betriebsanleitung Seite 17

Changing the quick change chuck
for SDS-plus
For HR002G/HR004G
The quick change chuck for SDS-plus can be easily
exchanged for the quick change drill chuck.
Removing the quick change chuck
for SDS-plus
CAUTION:
Before removing the quick change
chuck for SDS-plus, be sure to remove the bit.
Grasp the change cover of the quick change chuck for
SDS-plus and turn in the direction of the arrow until
the change cover line moves from the
the symbol. Pull forcefully in the direction of the arrow.
► Fig.7: 1. Quick change chuck for SDS-plus
2. Change cover 3. Change cover line
Installing the quick change drill chuck
Check the line of the quick change drill chuck shows
the symbol. Grasp the change cover of the quick change drill
chuck and set the line to the
drill chuck on the spindle of the tool. Grasp the change cover of
the quick change drill chuck and turn the change cover line to
the symbol until a click can clearly be heard.
► Fig.8: 1. Quick change drill chuck 2. Spindle
3. Change cover line 4. Change cover
Selecting the action mode
NOTICE:
Do not rotate the action mode chang-
ing knob when the tool is running. The tool will be
damaged.
NOTICE:
To avoid rapid wear on the mode
change mechanism, be sure that the action mode
changing knob is always positively located in one
of the three action mode positions.
Rotation with hammering
For drilling in concrete, masonry, etc., rotate the action
mode changing knob to the
carbide tipped bit (optional accessory).
► Fig.9: 1. Rotation with hammering 2. Action mode
changing knob
Rotation only
For drilling in wood, metal or plastic materials, rotate
the action mode changing knob to the
twist drill bit or wood drill bit.
► Fig.10: 1. Rotation only
Hammering only
For chipping, scaling or demolition operations, rotate
the action mode changing knob to the
bull point, cold chisel, scaling chisel, etc.
► Fig.11: 1. Hammering only
All manuals and user guides at all-guides.com
symbol to
symbol. Place the quick change
symbol. Use a tungsten-
symbol. Use a
symbol. Use a
Hook
CAUTION:
Always remove the battery when
hanging the tool with the hook.
CAUTION:
Never hook the tool at high loca-
tion or on potentially unstable surface.
The hook is convenient for temporarily hanging the tool.
To use the hook, simply lift up hook until it snaps into
the open position. When not in use, always lower hook
until it snaps into the closed position.
► Fig.12: 1. Hook
► Fig.13
Connecting lanyard (tether strap) to
the hook
CAUTION:
Do not use damaged hook and
screws. Before use, always check for damages,
cracks or deformations, and make sure that the
screws are tightened.
CAUTION:
Make sure that the hook is
securely installed with the screws.
CAUTION:
Do not install or remove any
accessory while hanging the tool. The tool may fall
if the screws are not tightened.
CAUTION:
Always use a locking carabiner
(multi-action and screw gate type) and be sure
to attach the lanyard (tether strap) to the double
looped portion of the hook. Improper attachment
may cause tool drop from the hook and result in
personal injury.
The hook is also used for connecting the lanyard (tether
strap). Be sure to connect the lanyard (tether strap) to
the double looped portion of the hook.
► Fig.14: 1. Double looped portion of the hook
2. Lanyard (tether strap) 3. Locking cara-
biner (multi-action and screw gate type)
Adjusting the nozzle position of the
dust collection system
Optional accessory
Push in the guide while pushing up the guide adjust-
ment button, and then release the button at the desired
position.
► Fig.15: 1. Guide 2. Guide adjustment button
NOTE: Before adjusting the nozzle position, release
the nozzle forward completely by pushing up the
guide adjustment button.
If a long drill bit is installed, extend the guide by pushing
up the extension button.
► Fig.16: 1. Extension button
17 ENGLISH