Care And Maintenance - Graphite 58G083 Betriebsanleitung

PREPARATION TO WORK
ASSEMBLY / REMOVAL OF THE SHORT LANCE WITH NOZZLE
• Pull the locking ring (9) back, insert the tip of the nozzle (8) into
the hole of the short lance (10)
• (fig. A).
• Release pressure on locking ring (9), check correct connection.
• The removal of the nozzle takes place in the reverse order of its
assembly.
WARNING! Check that the spray nozzle is properly secured.
INSTALLATION / REMOVAL AND HANDLE PISTOL LANCE
• Connect the short lance (10) with the pistol grip (4) of the device
by gently pressing (paying attention to the notches in the
connection) and turning it 90
• (fig. B).
• The long lance (7) is installed in the same way (Fig. C)
• The lance is disassembled in the reverse order to its assembly.
ASSEMBLY / DISASSEMBLY OF THE SHORT AND LONG
LANCE
• Connect the two lances by gently pressing (paying attention to
the notch in the joint) and turning by 90
(fig. D).
• Lances are disassembled in the reverse order to their assembly.
OPERATION / SETTINGS
CHOOSE YOUR WATER SOURCE
Connecting water from the tank
• Attach the quick-connect hose (15) to the socket (5) of the
appliance (fig. E).
• Place the hose (14) with the filter (16) in the water tank, position
the float (17) so that it remains on the water surface and secure with
the clip with the handle (18). The clip with a handle (18) should be
clamped on the hose (14) and hung on the wall of the tank.
WARNING! After connecting the hose, check the connection
by gently pulling on the hose.
WARNING! Do not use the device with a water source that is
cloudy, muddy, or corrosive. Suitable water sources: Bucket /
waterbag / ditches / canals / lakes / sea (The system must be
flushed completely with fresh water after use) (fig. F).
WARNING! When using open water (ditches / canals / lakes
etc), make sure the filter stays far from the bottom (move the
float if necessary). Always use the supplied filter hose.
WARNING! Before use, remove the air from the hose, hold (max.
1.5 m above the water source) and turn on the device. It may take
about 30 seconds for water to reach the machine.
Water connection from the mains
• Disconnect the hose (14) from the machine using the quick-
connect hose (15).
• Connect the adapter with valve (11) to the connection piece (5)
of the device (fig. G).
• Connect the garden hose to the nipple of the valve adapter (11)
(use a standard water hose with a suitable quick coupler).
WARNING! Always use the supplied adapter with valve for
mains water (drinking) water supplies. It is recommended to close
the adapter valve when the device is not in use (an open valve
causes water to flow out of the nozzle at the specified
pressure).
°
clockwise
°
in relation to each other.
WARNING! The water that has flowed through the adapter is
considered unfit for drinking.
ON / OFF
WARNING! Before starting work, make sure the battery is fully
charged.
Turn on - Press the trigger lock button (1) and pull the trigger
(2) (Fig. H).
Turn off - Release pressure on trigger (2).
PRESSURE SETTING
The device has two pressure settings. The high pressure setting is
suitable for thorough removal or cleaning, and the low pressure setting
is suitable for light cleaning and watering. The device is normally set to
high pressure mode. Press the pressure button (Eco) (3) to activate
the low pressure mode (fig. I).
SPRAY MODE SELECTION
Spray options are selected by turning the front nozzle ring (8).
Select the spray mode according to the type of work. The 0 ', 15', 25 ', 40'
and Jet spray settings are suitable for cleaning and the positions with the
spray symbol are best for watering (fig. J).
WARNING! Do not change the spray setting after turning on the
machine.
DETERGENT SPRAY ASSEMBLY
WARNING! Always use the detergent spray nozzle (12) in
combination with the long lance (7) only.
• Attach the long lance (7) to the device (fig. C).
• Attach the detergent spray nozzle (12) to the long lance (7)
connected to the machine (fig. K).
• Unscrew the detergent container (13) from the detergent spray
nozzle (12) and fill with the appropriate cleaning agent.
• Reattach the detergent container (13) to the detergent spray
nozzle (12).
• Aim the detergent spray nozzle (12) at the surface to be coated
with detergent and release the trigger lock button (1).
• Press the trigger (2) and then the pressure button (Eco) (3) if
necessary to activate the low pressure mode (the detergent placed in
the tank will be sucked in and mixed with the water).
• After finishing work, empty the detergent container.
WARNING! When using the water (drinking) network, make
sure that the water supply is blocked (for example by the
adapter valve (11)) when not using a shower. This prevents
the detergent from emptying the tank.
WARNING! The pressure washer was designed to work with
cleaning agents recommended by the manufacturer. The use
of other cleaning agents may adversely affect the safety of
the appliance. Do not use acids, gasoline, kerosene or other
flammable liquids as a cleaning agent. Only household
detergents (p H 6-8) may be used.

CARE AND MAINTENANCE

WARNING! Before starting any installation, adjustment, repair
or maintenance activities, remove the battery from the device.
MAINTENANCE AND STORAGE
• After each use, wipe the outer casing with a cloth.
• Do not use any cleaning agents or solvents as these may damage
the plastic parts.
• Be careful not to let water get inside the device.
9