Unpacking And Inspection - JSP PowerCap Active IP Benutzer-Bedienungsanleitung

UNPACKING AND INSPECTION: The following items should all be within the carton:
ITEM
PowerCap Active Lite
® ™
PowerCap Active™ IP
®
Note: PowerCap ® Active™ also provides protection to EN 812, the BumpCap standard.
It should be noted that the special liner for this protection forms an integral part of the cap structure. Ensure that the bump cap liner is fitted into the Cap before use.
STORAGE: When not in use or during transportation, Powercap
from direct sunlight, not in contact with solvents and in such a manner that it cannot be damaged by physical contact with hard surfaces. Storage temperature should be between
5°C and 40°C and relative humidity not greater than 75%. During storage, the power cable should be disconnected from the PowerBox™1 battery pack.
LITHIUM ION POWERBOX™1 BATTERY PACK: When turned on, the Lithium Ion battery has green, amber
and red lights on the outside to show the level of charge; green being fully charged.
Charging the batteries: Switch off Powercap
charge point using the Micro USB cable provided. A 5-8 hour charge will produce 8 hours of run time from
Powercap Active .
® ™
Precautions on charging:
• Avoid charging in direct sunlight or in a vehicle parked under direct sunlight, and make sure to charge only
when the ambient temperature is between +5°C and +40°C.
• Before charging, ensure that no dust or other foreign objects attach to the USB plug.
• Do not subject the device to vibrations while charging.
• When your PC is in sleep state, the unit cannot be charged.
• Once charging is complete, ensure that the USB plug is disconnected.
• If the function time is significantly reduced even after proper charging, the rechargeable battery may be
nearing the end of its service life.
• Dispose of batteries in accordance with local regulations.
USING THE PowerCap Active Unit: The Powercap
® ™
Operating temperature should be between 5°C and 40°C and relative humidity not greater than 75%.
FILTERS: The filters provided are high efficiency sub-micron particulate types supplied in pairs. They will filter most particulate matter such as dust, spores, mist and fumes, but like
all filters cannot filter out all particulate matter present in the air. They will not filter gases, vapours or toxic substances.
• The duration of filter life will depend mainly on the amount and size of the contamination in the area where they are used, and the time used in that area. Inspect the filters regularly.
Ensure that they are located correctly and carefully remove any visible large surface contamination to prolong their life. The filters must not be washed or allowed to get wet. A low
airflow reading (red section of indicator) usually indicates that new filters are required.
FITTING AND REPLACING THE FILTERS: Only replace with a pair of genuine replacement filters (at the same time) from JSP Ltd or its distributors.
Simply twist anticlockwise, with filter towards you, and lift away from motor housing (Image 1). Replacement is the reverse procedure. Ensure that the filter and motor housing mating faces
are clean; do not allow any dust or foreign objects to fall into the motor housing. Push and twist the replacements firmly into place (Image 2). Recheck airflow when the new filters have
been fitted before use. If the filters are not fitted correctly, filtering efficiency will be severely reduced.
1
REPLACING THE PRE FILTER PAD: The Powercap
the label of the filter, remove this lid, replace the pre filter pad and replace the cover ensuring that it is back in place correctly. Regular replacement of the pre-filter pad will help the air
flow of the product. The pre filter pad helps to protect from the larger airborne hazards (>10µm) whilst the actual filter protects from the smaller airborne hazards.
BATTERY AND AIRFLOW CHECK: Powercap
battery charge and airflow the filters must be fitted and the visor removed (See Image 3). Removal of visor for
airflow check is only relevant to Non-Impact Powercap
Having removed the visor insert the male connector at the end of the Powercap
female connector on the PowerBox
Switch the unit on using the switch located on the PowerBox™1 battery unit (See Image 5). Airflow will now
commence. It is now necessary to check that the airflow is sufficient, and the following checks should be carried
out on a regular basis with the filters fitted and always before use of Powercap
Invert (turn upside down) the Powercap
the rim of the Visor Carrier ensuring a good seal. Avoid placing hands or other possible obstructions over the
two filter inlets (See Image 6).
Check that the white 'flap' at the bottom of the Airflow Indicator moves freely. The "flap" indicator within the airflow device should
move into the "green section" which means that there is adequate airflow for PowerCap
In the event of no flow or low flow indicated by a move of the flap into the "red section", first recheck the battery
fitting or charging condition. In the event that there is still no or low airflow, do not use the PowerCap
but contact JSP Ltd for further advice.
Fitting the visor - PowerCap ® Active™ Lite:
1. Remove the old visor by peeling it away from the Velcro
2. Align the Velcro ® sections on the visor with the Velcro
that the visor is firm against the underside of the brim.
Cap c/w rigid PowerCap
®
Impact-Liner Drive Unit
3 3
3 3
Active
®
Active , remove the dust cover, and connect it to a USB
® ™
Active meets the TH1P requirements of EN12941 this offers protection against fine non-toxic fibres, fumes and dusts.
® ™
Removal
Active filter includes a pre filter cover that is situated underneath the grill lid of the filter. There is a removable lid just above
® ™
Active has a Minimum Design Flow rate of 140 l/min. To check
® ™
.
®
1 battery compartment (See Image 4).
™
Active and fit the Airflow Indicator supplied over the air outlet inside
® ™
®
sections on the inside of the brim.
® sections on the inside of the brim, ensuring that the visor is central. Press the Velcro
EN
Active™ 1mm
Polycarbonate Visor
3
should be stored in the packaging in which it was supplied. Powercap
™
2
Active "Power cable" into the
® ™
Active :-
® ™
Active to be used.
® ™
Active
®
2
0.35mm PowerBox™1
Polycarbonate Visor Battery Pack
3 3
3
Replacement
3
5
,
™
®
Airflow Test Unit
3
3
Active should be stored away
® ™
4
6
sections together making certain