Contents Welcome Disclaimer Specifications Part 1- Unboxing & Checking Package Contents Part 2- Mechanical Installation Part 3- Wiring Part 4- Software Setup Part 5- Test Project Part 6- Z Probe Setup Part 7- Offline Controller...
Welcome Thank you for purchasing the Genmitsu 3018-PROVer V2 CNC Machine from SainSmart. Included in your package will be a USB Stick, you will find: https://docs.sainsmart.com/3018-prover-v2 support@sainsmart.com Scan QR code to join the group...
Disclaimer dangerous areas. with the machine. Router into an extension cord, or power strip as it may damage the machine. operating.Serious injury may oCcur. during operation.
Specifications Model Name 3018-PROVer V2 Control Board Compatibility GRBL 1.1h TB67S109 32 bit Max Speed , UGS Plastic Leadscrew Control Software Motion System Spindle Motor 775 motor, 12V~24V, 000 RPM Stepper Motor Power Supply...
Part 1- Unboxing & Checking Package Contents Spindle Offline Controller Power Supply...
Seite 7
Offline Controller Cable Z-Probe Kit 20-degree V Bit Cable Tie User Manual 3mm, 5mm...
Seite 8
Optional Accessories (Not Included) Consider following optional upgrades or accessories to make your CNC experience better! Compressed Spot CNC Cutter Milling Laser Module...
Part 2- Mechanical Installation 2.1 Preparing your base assembly What you will need 3mm, 5mm Step 1: Step 2: seat as shown below. Step 3: Screws Holes of the Spoilboard Centered Screw Holes Nut Seat of the Nut Seat...
Seite 10
2.2 Installing Rubber Feet to Y-Axis Base Assembly What you will need 3mm, 5mm Step 1:...
Seite 11
2.3 Install Y-Axis Base to X / Z Axis Gantry What you will need 3mm, 5mm Step 1: Step 2: Screw Holes of...
Seite 13
2.4 Installing the Spindle What you will need Spindle 3mm, 5mm Step 1: Unscrew the black collar from the spindle and insert the collet. Make sure the collet is locked in place by pushing Step 2: Loosen the Spindle Mount Hex Screw. Step 3:...
Seite 15
2.5 Install the Acrylic Baffles What you will need 3mm, 5mm Step 1: Step 2: Place T-Slot nuts into the side of the machine so that the baffle is aligned with the edge of the frame. 2-3mm 20M5 T-Slot Nut...
Seite 16
Step 3: Now tighten the M5 bolts to secure the baffle. Repeat the steps to install the other side.
Part 3- Wiring Black Positi e Pole Negati e Pole...
Seite 18
shown below. Motor Socket Cable Socket...
Seite 19
Cable Management What you will need Cable Tie 1. Use the cable ties to fix the cable management on the cable holder as shown below. the cables. Cable Tie...
Seite 20
Tips for Installing the Clamps Please refer to the below images to install the clamps. Make sure that the screw screwing depth can not exceed the bottom of the aluminum platform, otherwise the screw will hit the frame of the machine. Screw The Bottom of the Screw...
Seite 21
Diagram X-axis Motor Z-axis Motor Spindle Motor Handwheel Laser Module USB Connecting Cable Power Switch Power Supply Z-Height Offline Controller Mapping Probe Stopping Switch...
Seite 22
Label Description Marker Instruction Power 24V Power Interface USB Interface Offline controller Offline Control Interface Probe X-LIM Z-LIM Laser Laser Module Interface Spindle Spindle Motor Interface...
Seite 24
2. To Determine your Machine's COM port: Windows XP: Windows 7: Click "Start" Right click"Computer" Select "Manage" If there are multiple USB serial ports, right click each one and check the manufacturer, the machine will be "CH340".
Seite 25
3. Grblcontrol (Candle) Connecting to the Controller Step 1: Software should automatically select the port number. Step 2: Step 3:...
Seite 27
2. Run G code for processing 1. Click [open], Select the G code to run. workpiece just touch. 4. Click [Send] running G code. 3. About firmware parameters...
Part 7- Offline Controller The offline interface is designed according to our offline controller and does not match with other companies' offline controllers.Do not connect other devices or controllers, or risk damaging the control board or other devices. 1. Button Functions Introduction Marker Instruction Manual moving distance option (xC, x0.01, x0.1, x1) in xC mode,...
Seite 32
2. Parameter Settings igure 1 igure 2 Function Instruction Spindle RPM Spindle speed Probe Tool Height Modify the height of Z Probe Z Rise Height Select...
Seite 33
3. Introduction of Control Functions Select the "Prepare" screen icon, as shown below: Function Instruction Spindle Probe Z-axis automatic tool setting Home Start Project Reset Reset the router Jog Step: xC mm...
Seite 34
4. Run the G-code program Processing Figure 2 Figure 1 time Coordinates Figure 4 Repeat Figure 3 processing Machine status Processing progress...
Seite 35
5. Machine Alarm and Solutions stop button. Figure 1 Figure 2...
Seite 36
Inhalt Willkommen Warnhinweise Specifications 1 – Lieferumfang 2 – Mechanischer Zusammenbau 3 – Elektrischer Anschluss 4 – Software Einrichtung 5 – Test Projekt 6 – Z Probe Einstellungen 7 – Offline Controller...
Willkommen https://docs.sainsmart.com/3018-prover-v2 support@sainsmart.com https://www.facebook.com/groups/SainSmart.GenmitsuCNC Scannen Sie den QR-Code, um der Gruppe beizutreten...
Seite 47
2.4 Montage des Spindelmotors Was wird benötigt: Spindelmotor mit Schritt 1: sicher, dass das Spannfutter durch Schieben arretiert wird. Schrauben Sie dann den Spannring wieder auf die Spindel. Schritt 2: Schritt 3:...
Seite 48
Schritt 4: Sechskantschraube der Spindelbefestigung...
5 – Test Projekt 1. Grblcontrol(Candle) linke Maustaste, um den einen Computer mit Grafikkarten wechseln. Manuelles Bedienfeld G-Code an Befehl senden Befehlseingabefeld Befehl senden Steuerbaugruppe senden...
Seite 61
2. G-Code zur Bearbeitung ausführen 2. Klicken Sie auf das manuelle Bedienfeld. 3. Über Firmware Einstellungen...
6 – Z Probe Einstellungen Übersicht der Funktionalität 1. Grblcontrol (Candle) Probe Anleitung Schritt 1: Probe Befehle bearbeiten werden. G-Code für Messwerkzeug Nach der Bearbeitung Dicke des Messwerkzeugs...
Seite 63
Schritt 2: Befehle für Messwerkzeug in Grblcontol(Candle) eingeben Befehle ein...
Seite 64
Schritt 3: Schließen Sie das Messwerkzeug an die entsprechende Schnittstelle der Steuerbaugruppe an. Schritt 4: Klicken sie auf "Z-probe" um die Z-Achse automatisch auf 0 zu setzen.
7 – Offline Controller Die Offline-Schnittstelle ist für unseren Offline-Controller konzipiert und passt nicht zu den Offline-Steuergeräten anderer Hersteller; schließen Sie keine anderen Geräte oder Steuergeräte an, sonst riskieren Sie eine Beschädigung der Steuerbaugruppe oder anderer Komponenten. 1. Funktionserläuterung der Schaltflächen Label Funktion Manuelle Verfahrweg Option (xC, x0.01, x0.1, x1) in xC-Modus, drücken...
Seite 66
2. Parametereinstellungen Label Funktion Spindle RPM Probe Tool Height Z Rise Height Bewegen Sie den Cursors Select...
Seite 67
3. Einführung in die Kontrollfunktionen Label Funktion Spindle Probe Home Start Project Reset Jog Step: xC mm...
Seite 68
4. G-Code ausführen Abbildung 2 Abbildung 1 Koordinaten Abbildung 4 Abbildung 3 der Bearbeitung Beenden Status der Maschine Status der Bearbeitung...
Seite 69
5. Beenden des Alarms Abbildung 1 Abbildung 2...