Gardena PowerMax 37/36V P4A Betriebsanleitung Seite 13

v Do not disassemble the product further than the delivery status.
v Use gloves, wear slip resistant shoes and wear eye protection.
v Only start the mower with an upright standed handle.
v Do not overload the mower.
v Never operate the product when you are tired, ill or under the influence of
alcohol, drugs, or medicine.
2. ASSEMBLY
DANGER!
Cutting injury due to the blade!
Risk of cut injury due to accidental starting.
v Use gloves.
v Wait for the blade to stop.
v Remove the safety key.
2.1 To assemble the handlebar [ Fig. A1 ]:
1. Fold both levers (S) outwards.
2. Turn both handlebar holders
3. Push both levers (S) to the handlebar
4. Unscrew the two pre-assembled screws
holders (2) .
5. Push the handlebar (1) into the handlebar holders
Make sure that the handlebar is completely in place and the holes of
the handlebar are inline up with the holes of the handlebar holders.
(3)
6. Put both screws in the holes of the openings
7. Tighten both screws (3) with a screwdriver.
Make sure that the screws are completely tightened.
2.2 To attach the cable to the handlebar [ Fig. A2 ]:
(4)
v Attach the cable to the clamps
Make sure that the cable is not trapped between the handlebar and
the mower, otherwise the cable may be damaged.
2.3 To assemble the grass catcher bag [ Fig. A3 ]:
1. First Push the tongue (6) into the two connectors
(8)
the grass catcher bag
Make sure that both connectors are engaged.
(6)
2. Then Push the tongue
catcher bag (8) until the connection audibly engages.
Make sure that the connector is engaged.
3. First push the catcher bag handle
(11)
cover .
4. Then push the catcher bag handle
(11)
cover until the connections audibly engages.
Make sure that all connectors are engaged.
3. OPERATION
DANGER!
Cutting injury due to the blade!
Risk of cut injury due to accidental starting.
v Use gloves.
v Wait for the blade to stop.
v Remove the safety key.
3.1 To charge the battery [ Fig. O1 / O2 / O3 ]:
CAUTION!
The voltage of the power source must match the voltage specified on
the rating plate of the charger.
v Note the mains voltage.
For the GARDENA Battery Mower Art. 14638-55 there is no battery
and no charger in the scope of delivery.
14638-20.960.03.indd 13 14638-20.960.03.indd 13
(2) to the operating position.
(1) .
(3)
from the handlebar
(2) .
(2)
in the mower.
(5) (1)
on the handlebar .
(7) at the bottom of
until the connections audibly engages.
(9)
into the connector on the side of the grass
(10) at the back into the catcher bag
(10) at the front into the catcher bag
Thanks to the intelligent charging process, the charge condition of the
battery is automatically detected and then charged up with the optimal
charge current depending on battery temperature and voltage.
In this way, the battery is treated with care and remains permanently fully
charged when it is stored in the charger.
1. Open the batterie cover (18) .
2. Push the locking button (A) and remove the battery
(D)
holder .
3. Connect the battery charger (C) into a mains socket.
4. Slide the battery (B) onto the battery charger
When the battery charge indicator
the battery is being charged.
When the battery charge indicator
manently green the battery is completely charged
(Charging time, see 7. TECHNICAL DATA).
5. Examine the charge status regularly while you charge.
6. When the battery (B) is completely charged, the battery
(C)
disconnected from the charger
3.2 Meaning of the indication elements:
3.2.1 Indication on the charger [ Fig. O3 ]:
(Fast) Blinking of the The rapid-charging procedure is indicated by fast blinking of the
Green Battery Charge green battery charge indicator
Indicator (Lc)
Note: The rapid-charging procedure is only possible when the battery
temperature is within the allowable charging temperature range,
see 7. TECHNICAL DATA.
(Slow) Blinking of the When the charging condition of the battery is 80 %, the green battery
Green Battery Charge charge indicator (Lc) blinks slowly.
(Lc)
Indicator
The battery can be removed for immediate use.
Continuous lighting of the green battery charge indicator
Continuous Lighting
that the battery is fully charged.
of the Green Battery
(Lc)
Charge Indicator
When the battery is not inserted, continuous lighting of the battery
(Lc)
charge indicator indicates that the mains plug is inserted in the
Full
socket outlet and that the battery charger is ready for operation.
Continuous lighting of the red battery error indicator
Continuous Lighting
that the temperature of the battery is not within the allowable charging
of the Red Battery
temperature range, see 7. TECHNICAL DATA.
Error Indicator (Wc)
As soon as the allowable charging temperature range is reached, the
battery charger automatically switches to rapid charging.
A blinking red battery error indicator
Blinking Red Battery
of the charging procedure, see 6. TROUBLESHOOTING.
(Wc)
Charge Indicator
3.2.2 Battery charge status indication
[ Fig. O4 / O8 ]:
After starting the product, the battery charge status indication
is displayed for 5 seconds.
Battery charge status indication
(L1) (L2) (L3)
, and light green
(L1) and (L2) light green
(L1)
lights green
(L1)
blinks green
If the LED (L1) blinks green, the battery must be charged.
(Wp)
If the error LED is lighting or blinking see 6. TROUBLESHOOTING.
3.2.3 Eco button:
The Eco mode reduces the motor speed to 3100 rpm for a maximum
battery lifetime.
3.2.3.1 To activate the Eco mode:
(e)
v Push the Eco button on the control panel.
The Eco mode is activated and the LED
3.2.3.2 To deactivate the Eco mode:
(e)
v Push the Eco button on the control panel.
The Eco mode is deactivated and the LED
(B) from the battery
(C) .
(Lc) at the charger blinks green
(Lc) at the charger lights per-
(B) can be
.
(Lc)
.
(Lc)
indicates
(Wc)
indicates
(Wc) indicates a different malfunction
(P) on the product
(P)
Battery charge status
67 – 100 % charged
34 – 66 % charged
11 – 33 % charged
0 – 10 % charged
(Le) lights.
(Le) is off.
25.07.22 11:01 25.07.22 11:01
13