Firmware Update - ELAC VARRO Dual Reference-Serie Bedienungsanleitung

Firmware Update

Filename: elac 1019_10PR amp panel silk Rev B.ai
1 Color: White
SCI P/N: SLK3550
Rev: B
Dual Reference Subwoofer Series
Model : DS1000-GB
LEFT LEFT
LINE
IN
RIGHT RIGHT
SPEAKER LEVEL
INPUTS
RIGHT/
LEFT
LFE
WIRELESS
PAIR/RESET
THIS DEVICES COMPLIES WITH PART 15 OF THE FCC RULES
OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS:
1 THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE
2 THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED
INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED
VOLUME
OPERATIONS
CONTAINS FCC ID: A8TBM70ABCDEFGH
CONTAINS IC ID: 12246A-BM70BLES1F2
CONTAINS FCC ID: NKR-SWA12
CANTAINS IC: 4441A-SWA12
12V
CAN ICES-3(B)/NMB-3(B)
TRIGGER
SERVICE
ETHERNET
1. Unzip the downloaded firmware file and place the "FIRMWARE_UPDATE_FILE.BL2"
CAUTION
For continued protection against
risk of fire, replace only with same
type fuse and rating
SERIAL NUMBER
file in the root directory of a FAT32 formatted USB flash drive. exFAT, NTFS and other
1938 N. Batavia St. Suite K
Orange, CA 92865
ATTENTION
Utiliser un fisible de rechange
Fraunhoferstraße 16
de meme type et calibre
24118 Kiel file systems are not compatible.
Deutschland
www.elac.com
2. Power off the subwoofer, wait 5 seconds and plug the USB flash drive into the USB
POWER
port on the rear of the subwoofer.
ON
T12A H 250V
T6.3A H 250V
OFF
3. Power on the Subwoofer. The firmware update will automatically begin.
100-120VAC 50/60Hz 12A 220-240VAC 50/60Hz 6.3A
4. The firmware update will be complete when the LED on the rear of the subwoofer
Desinged by Elac Made in China
stops flashing.
5. Power Cycle the subwoofer. The firmware update is now complete.
6. You can check the firmware version of the subwoofer in the Sub Control 3.0 app on
the about page.
Reset
Filename: elac 1019_10PR amp panel silk Rev B.ai
1 Color: White
SCI P/N: SLK3550
Rev: B
Dual Reference Subwoofer Series
Model : DS1000-GB
LEFT
LEFT
LINE
IN
RIGHT RIGHT
SPEAKER LEVEL
INPUTS
RIGHT/
LEFT
LFE
WIRELESS
PAIR/RESET
THIS DEVICES COMPLIES WITH PART 15 OF THE FCC RULES
OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS:
1 THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE
2 THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED
INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED
VOLUME
OPERATIONS
CONTAINS FCC ID: A8TBM70ABCDEFGH
CONTAINS IC ID: 12246A-BM70BLES1F2
CONTAINS FCC ID: NKR-SWA12
CANTAINS IC: 4441A-SWA12
12V
TRIGGER CAN ICES-3(B)/NMB-3(B)
SERVICE
ETHERNET
CAUTION
For continued protection against
risk of fire, replace only with same
type fuse and rating
SERIAL NUMBER
1938 N. Batavia St. Suite K
Orange, CA 92865
ATTENTION
Utiliser un fisible de rechange
Fraunhoferstraße 16
de meme type et calibre
24118 Kiel
Deutschland
1. Press and hold down RESET button for minimum of 10 seconds
www.elac.com
2. LED starts to blink (flash). LED blinking parameters: LED is on for 100 ms (milliseconds) then LED is off
POWER
ON
for 100 ms.
T12A H 250V
T6.3A H 250V
OFF
3. Release the RESET button before 15 seconds elapses in order to force the sub to perform Factory
100-120VAC 50/60Hz 12A 220-240VAC 50/60Hz 6.3A
Desinged by Elac Made in China
Reset
4. If the RESET button is hold down for more than 15 seconds Factory Reset is cancelled.
ELAC Dual Reference Subwoofer Models DS1000, DS1200 | www.elac.com
Note:
Firmware for your subwoofer can be downloaded from
www.elac.com under the troubleshooting and firmware
section.
USB drive must be compatible with USB 2.0 with a 512
byte hardware sector size.
Note:
RESET erases all data and restores subwoofer firm-
ware and parameters to the original factory settings.
Firmware upgrade may be necessary post RESET.
Page 5