Disassembly; Troubleshooting Guide - Kärcher FC 2-4 Bedienungsanleitung

ATTENTION
Material damage due to loose roller
This may damage the washing machine.
Place the roller in a laundry net and load the washing
machine with extra laundry.
1. Bring the device handle into a vertical position.
The device switches off.
2. Place the device in the parking station.
Illustration R
3. Press the unlocking button for the side cover and re-
move the cover.
4. Pull the cleaning roller out via the recessed grip.
Illustration M
5. Clean the cleaning roller under running water or
wash it in the washing machine at max. 60 °C.
Illustration O
6. Clean the roller drive with a moist cloth.
7. To dry, place the wet roller on the pedestal of the
floor head.
Illustration S
8. Store the device in a dry room.
Illustration U
Cleaning the hair filter
ATTENTION
Adhering dirt deposits
Adhering dirt deposits can damage the device in the
long term.
It is recommended to clean the device completely after
each application.
ATTENTION
Adhering dirt deposits
Adhering dirt deposits can damage the device in the
long term.
Clean hair filter regularly with the cleaning brush.
ATTENTION
Damage due to cleaning the hair filter in a dish-
washer
The washing process can distort the scraper edge and
it will no longer press on the roller correctly. This wors-
ens the cleaning result.
Do not clean the hair filter in a dishwasher but rather un-
der running water.
1. Bring the device handle into a vertical position.
The device switches off.
2. Place the device in the parking station.
Illustration R
3. Press the hair filter unlocking button.
Illustration L
The hair filter is released and can be removed.
4. Clean the hair filter under running water.
5. Remove adhering dirt deposits, e.g. in the filter
comb, using the cleaning brush.
Illustration P
Illustration Q
6. Fit the hair filter into the floor head at a 45° angle
and then press it down until it audibly latches into
place. The hair filter must sit tightly in the device.
Illustration T
Cleaning and care agents
ATTENTION
Use of unsuitable detergents and care agents
The use of unsuitable detergents and care agents can
damage the device and loss of eligibility for warranty
claims.
Use only KÄRCHER detergents.
Take care to ensure the correct dosage.
Note
Use KÄRCHER detergent or care agents for floor clean-
ing as necessary.
 Observe the manufacturer's dosing quantity recom-
mendations when dosing with detergent or care
agents.
 To prevent foaming, fill the fresh water tank with wa-
ter first and the add the detergent or care agent.
 To prevent the tank from overflowing, be sure to
leave enough space for the detergent or care agent
when filling with water. To do this, observe the Max
marking on the fresh water tank.
Removing the device handle
ATTENTION
Frequent removal of the handle
The handle components can be damaged by repeated
removal.
Do not remove the handle from the basic device after
assembly.
The handle may only be removed from the basic device
when the device is sent out for service purposes.
CAUTION
Risk of injury
Using a screwdriver on a lock poses the danger of slip-
ping and causing an incision injury.
Use the screwdriver carefully on the lock.
1. Removing the fresh water tank.
2. Using a screwdriver at a 90° angle, press the un-
locking button on the upper part of the device handle
and remove the upper part of the device handle.
Note: When pressing the unlocking button with the
screwdriver, only apply pressure carefully to avoid
damage to the device.
Illustration Y
3. Using a screwdriver at a 90° angle, press the un-
locking button on the lower part of the device handle
and remove the lower part of the device handle.

Troubleshooting guide

Malfunctions often have simple causes that you can
remedy yourself using the following overview. When in
doubt, or in the case of malfunctions not mentioned
here, please contact your authorised Customer Service.
The LED flashes quickly for 30s
The battery pack is overheated.
 Stop operation and allow the device and battery
pack to cool down.
The LED flashes five times in quick succession
The battery pack is not recognised.
 Remove the battery pack and press it back into the
battery pack holder on the device.
The battery pack must be charged.
 Charge the battery pack (see operating instructions
and safety instructions for the battery pack and the
charger).
The device does not work
The battery pack is not sitting properly in the device.
 Push the battery pack into the battery pack holder
on the device until it latches into place.
The charging state of the battery pack is too low.
 Charge the battery pack, see chapter Battery pack
charging.
English

Disassembly

15