Maintenance & Troubleshooting - Cadac Dometic 2 COOK 3 Gebrauchsanweisung

6. Cleaning
• It is recommended to clean your appliance after every use. This will prolong the life of your appliance.
• Allow the appliance to cool down before you clean it.
• Use a damp cloth wrung out in a solution of soapy water to clean exterior surfaces.
• To clean the stove body, simply wipe with a damp cloth using a little detergent, if necessary.
• DO NOT IMMERSE IN WATER as this will allow water to get into the burner tube causing the appliance to malfunction.
• The grill plate is coated with a tough durable ceramic non-stick coating that has been used with great success on some of the best cookware
in the world. Never the less, taking care of it can help you to enjoy extra years of healthy, easy, non-stick cooking.
• Whilst the ceramic non-stick coating is very durable, it can easily be damaged by the use of metal cooking utensils. It is therefore
recommended that only plastic or wooden utensils be used when cooking.
• Always allow the grill/flat plate to cool before immersing it in water.
• Make sure that no water gets onto the burners or pilot/light area. Wipe the appliance completely dry before use.
• Do not use abrasive cleaners as they may damage the surfaces.
• Clean the appliance after each use. After cleaning recondition the cooking surface with a light wipe of oil.
• Do not use any high-pressure steam equipment or a water jet to clean the appliance.
• Note: For stubborn stains, CADAC oven cleaner may be used.
7. Storage
• Always allow the unit to cool down and be cleaned before storing.
• Turn off the gas supply to the appliance, disconnect and remove the gas supply from the appliance.
• Never store an appliance with the gas supply connected, this is an unsafe practice.
• Store the appliance and gas supply in a well-ventilated area away from combustible material. Storage of cylinders should preferably be
outdoors and must NOT be in a basement.
8. Maintenance & troubleshooting
Maintenance
• If you clean and maintain your appliance on a regular basis, the life of your appliance will extend and the possibility of problems will
decrease.
• We recommend the service of your appliance to be every twelve (12) months by a service agent to ensure continued efficient operation.
• This appliance must only be serviced by an authorized person.
• Check your gas hose and connections regularly for any signs of leaks and every time the gas cylinder is re-filled or fitted to the appliance
with every use.
Troubleshooting
In the case of a spattering flame or jet blockage:
• Clean your burner ports in case of an over spill.
• We recommend to clean or replace the jets every six (6) months to ensure continued efficient operation of your appliance.
• Should the appliance operate abnormally after storage and all checks have not isolated the problem, the jet may be blocked. A blocked
jet would be indicated by a weaker yellowish flame or no flame at all in extreme cases. Under these circumstances it will be necessary to
remove and check and thoroughly clean out any foreign matter which may have gathered in the appliance.
• This may be done by removing the jet using standard tools and blow any dirt from the jet, alternatively, you may purchase new jets from your
local store. Do not attempt to clean the jet mechanically.
Replacing a Blocked Jet:
• Your appliance is fitted with a specific size jet to regulate the correct amount of gas.
• Should the hole in the jet become blocked, this may result in a small flame or no flame at all. Do not attempt to clean the jet with a pin or
other such device as this may damage the orifice, which could make the appliance unsafe.
• To replace the jet: Remove any cooking surfaces, close the lid and turn the appliance upside down. Gently unscrew the bottom panel by
removing the screws (Fig. 4)(Only for 203P1 models). Unscrew the screw for the affected burner(s) (Fig. 5), carefuly loosen and drop the
burner as illustrated, to expose the jet. Note that the burner is connected to the piezo cable, after replacing the jet and reassembling, check
that this cable is still connected. The jet can now be seen on the valve, remove the jet using a suitable spanner (Fig. 6). Do not use pliers on
the jet as this may damage the jet, making it unusable or impossible to remove. Screw the new jet into the valve. Do not over-tighten as this
may damage the jet.
• Reverse the above procedure to re-assemble the unit.
Replacing the Hose:
• The fitting of a hose is described in Section 2.
7 7
EN