Additional Safety Instructions - Collomix CMG 1700 Originalbetriebsanleitung

Additional safety instructions

► Wear protec琀椀ve goggles and
hearing protec琀椀on.
Do not touch the diamond cup disk un琀椀l it has
►
cooled down. Diamond cup disks become very
hot during opera琀椀on.
► Use a dust extractor when grinding stone. The
dust extractor must be cer琀椀昀椀ed for stone dust
extrac琀椀on. The use of these devices reduces
the hazards of dust.
► Do not grind any materials or workpieces con-
taining asbestos.
► Grip the power tool 昀椀rmly with both hands
while working and ensure a safe and 昀椀rm
stance. The power tool must be held 昀椀rmly in
both hands.
► Secure the workpiece. A workpiece held in a
clamping device or bench vise is be琀琀er secured
than when held by hand.
► Avoid any blockage of the diamond cup disk
or excessive contact pressure during grinding.
Excessive stresses on the grinding disk increases
its load and its vulnerability, i.e. it can easier get
stuck or blocked and the risk of recoil or break-
age of the grinding disk is increased.
► Switch o昀昀 the power tool if the diamond cup
disk gets blocked or you need to interrupt
your work for any reason. Hold the power tool
steady un琀椀l the disk has come to a complete
stands琀椀ll.
► Do not switch the power tool back on while
it is in contact with the workpiece. Allow the
grinding disk to reach its full speed before re-
commencing work.
► Only use the power tool with the protec琀椀ve
hood opened along wall edges. The protec琀椀ve
hood must always be closed when working on
昀氀at areas.
► Check the device, cable and plug before each
use. Any damage detected must only be re-
paired by a cer琀椀昀椀ed electrician. Connect the
wall plug only with the machine switched o昀昀.
► When working outdoors, operate the machine
with a residual current operated circuit-break-
er (RCD) with max. 30 mA.
► Pull the mains plug and check that the main
switch is in OFF posi琀椀on if you leave the ma-
chine una琀琀ended, e.g. during installa琀椀on or re-
moval work, in case of a voltage drop, or when
inser琀椀ng/ moun琀椀ng an accessory part.
► Switch o昀昀 the machine if it comes to a stand-
s琀椀ll for any reason. This will prevent any sud-
den run-up while the machine is una琀琀ended.
► Do not use the machine if any part of the hous-
ing is defec琀椀ve, or if any damage is detected
on the switch, power line or plug.
► Ensure that the rota琀椀onal speed stated on the
grinding disk is equal to or higher than the mo-
tor speed of the machine. Only use appropriate
accessory parts.
► The exterior diameter of the grinding cup must
match the measurements provided on the
power tool.
► Diamond cup wheels and 昀氀anges must 昀椀t ex-
actly onto the grinding spindle of your power
tool.
► Diamond cup disks must only be used for their
speci昀椀ed applica琀椀ons.
► The device may only be operated with the pro-
tec琀椀ve hood undamaged and fully func琀椀onal.
► Only use cup wheels which are smaller than
the lamellar ring of the protec琀椀ve hood.
► Replace the lamellar ring when it is worn.
Rev. 2 / 13
Read the opera琀椀ng manual of the ma-
chine before use and comply with the
instruc琀椀ons contained therein!
Wear protec琀椀ve goggles and hearing
protec琀椀on while working with the ma-
chine.
The use of a face mask is recommended
for dust-intensive tasks.
Wear protec琀椀ve gloves while working.