Bell Rackmaster 5D Bedienungsanleitung Seite 8

RM5D
Digital Audio Mixer
The Rackmaster 5D combines a fully
equipped digital audio mixer with echo/
reverb, bluetooth receiver, mp3 player,
startsignal generator, noise gate, talkover,
feedback eliminator and a high quality
DSP audio management.
Instead of a confusing number of switches,
potentiometers and knobs, the RM5D
comes with only three rotary encoders for
music, microfone and effect, with the EFF
VOL encoder having a double function as
Navigator through the menu.
Most functions of the RM5D are selected
vwrs uII
by the 5 key switches
the front side commander and the menu in
the 2" display. Parameters and values are
set by the rotary Navigator / EFF VOL.
User Mode / Admin Mode
The RM5D may be operated in two diffe-
rent modes:
User Mode (described in this manual)
This is composed for the user who needs
an easy to operate audio mixer. Stored
under User 1...4, he will find the most
useful settings.
Should the user ever get lost in his own
personal settings, he can easily restore the
original factory presets by reloading
User 1...4.
Restore User Presets:
uII
Button - SYS - Load User -
select 1..4 - by EFF VOL (NAV). Confirm by
uII
pressing - Display: Success - Exit
®
Admin Mode (Access Code required)
Admin mode requires a deeper audio engi-
neering knowledge. That is why the RM5D
is normally supplied in user mode only.
Admin mode enables the audio engineer
to prepare specific RM5D setups, so it will
work as a multi zone mixer in a leisure
park, as the main mixer in a funfair ride
with start signal, automute, noisegate and
echo/reverb effect or as a simple to opera-
te audio mixer in a children's carousel.
Every task is different - and with its
unique features the RM5D will master
nearly all of them.
of
Inputs - Audio Sources
Two Mic / Line channels
MIC1 / 2 channels are prepared to connect
dynamic microfones or audio sources with
line level output, such as jingle players.
MIC1 / Mic2 combo sockets, balanced. For
use of XLR connectors (3-pin, male) or
jack plugs, (6.3mm).
AUX1 / AUX2 input channels (RCA L/R)
connect a multi media player (i.e. BELL
MMP11), PC, tablet or smartphone with
AUX output or adaptor to RCA Cinch L/R.
Bluetooth (BLT)
connects with tablets, smartphones and
other sources with bluetooth.
To connect, BLT must be activated in the
uII - SYS - BLT Conn - EFF
RM5D menu.
VOL - reconnect - Exit.
uII
Select input source BLT:
Input - EFF VOL - BLT - Exit.
alternatively use IR remote control and
press INPUT until display shows BLT.
USB (Stick) Player
Reads and plays MP3 and other audio
tracks from a USB stick.
uII - SYS - Input - EFF
Select input USB:
VOL - USB - Exit.
Alternatively use IR remote control and
press INPUT until display shows USB.
technische Änderungen vorbehalten - specifications may change without notice
Start Signal Player
Plays (start) signals (mp3 and other audio
tracks) from a Micro SD card.
Should more than one track be stored on
the Micro SD card, the signal player will
play the next following track after the start
u has been pressed. (
button
LED ON).
Signal may either be started by the
u button, or via
SIGNAL
‚SIGNAL FS' on the rear panel.
Use a footpedal or any other potential
free momentary ON switch with a 6,3mm
jack plug.
Volume of start signal
Menu: SYS - Signal VOL. EFF VOL sets the
volume level in the range of 0....30.
Settings for Channels MIC1 und MIC2
MIC Gain (sensitivity), Bass, Middle and
Treble are separately set in the MIC
MENU for MIC Channel 1 / 2.
Access to MIC Menu
uII
- gets you to the menu. Pushing
twice opens the MIC Menu.
Selections and settings via
VOL (Navigator).
MIC Gain (-80 / +12dBu) matches the
signal source (microphone or line level) of
channels MIC1 / MIC2 separately.
When using a dynamic vocal microphone
(i.e. BELL M290V) MIC Gain of the channel
in use den (MIC1 or MIC2) should be set
to +6 ... +12 dBu.
uII - SYS -
Red signal
the jack socket
w
rs
and EFF