Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
and reception).
You can choose from the following settings:
OFF: TS-T9+ receives on both channels (not simultaneously);
will flash on the corresponding frequency band
A: TS-T9+ receives on both channels (not simultaneously) but transmits only on
channel A (upper).
B: TS-T9+ receives on both channels (not simultaneously) but transmits only on
channel B (upper).
If you choose option A, 465.575MHz is the transmission frequency, while
136.225MHz is the reception frequency;
If instead you choose option B, 136.225MHz is the frequency in tx and
465.575MHz is the frequency in rx.
Example: the display shows
Side tone elimination (STE) - Menu N°35
This function eliminates that annoying tone that is emitted at the end of transmis-
sion.
Side tone in
communication with repeaters (RP-STE) Menu N°36
This feature is useful when communicating with repeater bridges; when the PTT is
released, the repeater bridge will emit a tone to confirm its operation.
You can choose between these possibilities:
OFF
1,2,3,4,5, .... 10 to set the delay.
Note: we recommend disabling this function during normal use of the radio, so
as not to affect your conversations.
Delay setting for communication with repeater bridges (RPT-RL) - Menu N°37
With this function you have confirmation that the repeater bridge with which you
communicate has received your signal. You can choose between:
OFF
1,2,3,4,5, .... 10 (set the delay)
Display on power-up display (PONMSG) Menu N°38
In this menu, set the display to show when the radio is turned on. Two options are
possible:
FULL: the frequency appears.
MSG: Tech Side is displayed.
Roger beep (ROGER) - Menu N°39
When you release the PTT, the radio will beep to confirm to others
users who have finished your communication and the other parties can start broad-
casting.
Reset (RESET) - Menu N°40
The reset allows you to return the device to the original factory settings and param-
eters. Once reset, you can set the desired functions. Two types of reset are possible:
VFO: Menu reset
ALL: reset of Menu and channels
52
Keypad lock - Menu N°41
This function locks the keyboard to prevent accidental key presses.
or
To unlock the keyboard, press # for more than 2 seconds.
FM radio (FM) - Menu No°42
1.
The frequency band of the FM radio is 65-108MHz.
2.
In frequency or channel mode press CALL
3.
Select the desired radio station with the
cy directly.
4.
To change the station press *
5.
To exit FM radio mode press CALL.
Note: listening to the radio is automatically interrupted to transmit or if signals
are received on the channels or on the set frequencies.
Rapid alarm (ALARM) - Menu N°43
In frequency or channel mode, press CALL for more than 2 seconds: it comes
alarm tone emitted. To stop it, press PTT.
Note: for alarm mode, refer to Menu N°32.
Torch - Menu N°44
TS-T9+ is equipped with a torch for night lighting.
To turn it on, press MON; press the button again and the flashlight will flash strobo-
scopically. Press MON a third time to turn it off.
Monitor (MON) - Menu N°45
The Monitor feature allows you to override the squelch so you can receive signals
that are too weak to be received with the squelch open.
Press MON to activate or deactivate the function.
Channel / frequency mode (VFO / MR) - Menu N°46
To switch from channel to frequency mode, press the VFO/MR button.
1750Hz tone - Menu N°47
To send a 1750Hz tone, press PTT + BAND. This feature is useful for communica-
tions via repeater bridges.
Inverted frequency function (R) - Menu N°48
Thanks to this function, the transmission and reception frequencies can be inter-
changed: press the * key.
Note: the inverted frequency function can only be activated in the simplex mode
(same frequency tx and rx). However the frequency tx and rx does not change.
Frequency scan - Menu N°49
To scan frequency:
1.
In frequency mode, press * for more than 2 seconds. The radio will start scan-
ning frequencies according to the set frequency step.
2.
Use the
3.
To stop scanning, press any button.
Note: for scan mode, refer to Menu N°18.
Channel scan - Menu N°50
To scan channels:
1.
In frequency mode, press * for more than 2 seconds. The radio will start scan-
ning according to the set channel.
2.
Use the
3.
To stop scanning, press any button.
/
/
keys to reverse the direction of the scan.
/
keys to reverse the direction of the scan.
buttons or enter the frequen-
EN
53
Werbung
Inhaltsverzeichnis
