TechSide TS-T9+ Handbuch Seite 28

This function can be set from PC
Scan Resume Mode (SC-REV) - Menu N°18
Thanks to this function, Tech Side TS-T9+ is able to scan in frequency or channel
mode.
Select the preferred mode according to your needs.
TO - Time-operated Scan
Scanning stops when the radio receives a signal on a busy channel and will resume
after about 5 seconds, regardless of whether the signal persists.
CO: Carrier-operated Scan
Scanning stops on a busy channel until the signal is detected and will resume once
the radio no longer detects any signal.
SE: Search Scan
The radio stops on a busy channel and stops scanning.
Transmission of the PTT-ID identifier (PTT-ID) Menu N°19
Thanks to this function it is possible to choose when to send the ANI-ID code in
transmission. You can choose between 4 possibilities, listed below.
OFF: Press PTT to turn it off
BOT: the code is sent when the PTT is pressed
EOT: the code is sent when the PTT is released
BOTH: the code is sent when the PTT is pressed and released
Note: when you do not intend to use this function, select 'OFF' so as not to affect
the operation of the radio.
PTT send delay ID (PTT-LT) - Menu N ° 20
In this menu you can set the delay (0-30ms) in which the radio sends the PTTID
when the PTT is released.
Upper channel / frequency display mode (MDF-A) Menu No. 21
In this menu you can set the channel/frequency display mode on the top line (A) of
the display.
Display mode:
FREQ .: Frequency + channel number
CH: Channel number
NAME: Channel name
Note: the channel name mode must be set by the programming software; you
can type up to a maximum of 3 characters.
Lower channel / frequency display mode (MDF-B) Menu No. 22
In this menu you can set the channel / frequency display mode on the bottom line
(B) of the display.
Display mode:
FREQ .: Frequency + channel number
CH: Channel number
NAME: Channel name
Note: the channel name mode must be set by the programming software; you
can type up to a maximum of 3 characters.
Busy channel block (BCL) - Menu N°23
This function allows you to block interference from other radios: if you select a busy
channel, pressing the PTT button has no effect and the radio does not transmit.It
will broadcast again when the channel is free.
50
Keyboard lock (AUTOLK) - Menu N°24
This function avoids accidental key presses. When activated, the keyboard locks
automatically after 15s.
Frequency deviation (SFT-D) - Menu N°25
With this function you set the direction of the radio frequency offset.
This function is used in the use of the radio on repeater bridges.
You can choose from these options:
+: positive offset
-: negative offset
off: no offset
Note: Depending on the repeater bridges, a different frequency deviation must
be set. In channel mode this function cannot be changed.
Frequency offset (OFFSET) - Menu N°26
In this menu you set the frequency offset between tx and rx.
In the TS-T9+ the offset is 0-69.990MHz.
This feature is useful for communication with repeater bridges.
Channel memory - (MEM-CH) - Menu N°27
In standby or frequency mode, frequencies and parameters can be stored.
To set a CTCSS tone or a DCS code in tx or rx on the stored channel,
(paragraphs 10-13). Instructions for memorizing channel:
- Position yourself on the frequency to memorize
[MENU] - [27] - [MENU] - (find free memory with
Note: a stored channel cannot be overwritten, it must first be deleted. See follow-
ing paragraph Menu N°28.
Deleting a channel (DEL-CH) - Menu N°28
[MENU] - [28] - [MENU] - (Search for the channel to be deleted with the arrows
) - [MENU] - [EXIT]
Backlight (WT-LED) - Menu N°29
This function allows you to decide the lighting on / off
Reception backlight (RX-LED) Menu N°30
This function allows you to decide the lighting on / off
TX backlight (TX-LED) - Menu N°31
This function allows you to decide the lighting on / off
Alarm mode (AL-MOD) - Menu N°32
Thanks to this function you can set some types of alarm: tone alarm, code alarm
and site alarm.
To send an alarm tone, keep the CALL key pressed for 3 seconds.
SITE ALARM: TS-T9+ emits an alarm tone but the radio does not transmit it;
TONE ALARM: TS-T9+ emits an alarm tone and the radio transmits it;
CODE ALARM: TS-T9+ emits an alarm tone and the radio transmits the ANI-ID code.
Frequency band Shift (BAND) - Menu N°33
In frequency mode, press the BAND button to select the desired frequency band.
VHF: 144 - 146MHz / UHF: 430 - 440MHz
Dual Watch (TDR-AB) - Menu N°34
When the Dual Watch is activated (See Menu N° 7), signals can be received on the A
/ B channels or on the frequency.
It can also be used for the Cross band function
EN
/ ) - [MENU] - [EXIT]
/
51