Care And Maintenance; Technical Data - Status SD300 Originalbetriebsanleitung

6. OPERATION
Only use screw bits which are compatible with the screw head. Make sure that the
screw tools are only used with reduced rotation speed.
OPERATION
Special work advice
• Never place the drill socket key in the drill socket.
• Keep the handle dry and free from oil and grease.
• Make sure that there are no water pipes or electricity cables in or behind the
place or object to be drilled.
• Attach nuts and screws to the electric drill only when it is turned off.
NOTE: When operating a power tool outdoors, connect it to a residual current
circuit-breaker.
Turning on/off
• Connect the power plug to a power outlet.
• Attach the drilling machine directly to the drill spot.
• Press and hold the on/off button (4) to turn the
machine on.
• To turn the machine off, let go of the on/off button (4).
Setting the rotation speed
By pressing the on/off button (4), you can set the rotation speed during idle
operation. The optimal rotation speed depends on the material drilled,
the operation mode, and the inserted drill.
Light pressure on the on/off button:
low rotation speed (intended for: small/short screws, soft working materials)
Greater pressure on the on/off button:
higher rotation speed (designated for: large/long screws, hard working materials)
NOTE: To prevent the cracking of drill holes (e.g. when drilling tiles), drill holes
first with low rotation speed and then increase it. The drill is then easier to control
and will not slip.
Gear selection switch (SD300/2)
Do not set the gear selection switch (5) during drilling.
Gear 1 - low rotatio speed (0 - 370 RPM)
Gear 2 - high rotation speed (0 - 1050 RPM)
Setting the torque
The torque setting enables you to fix a screw perfectly without damaging the base
material or the screw head. The setting depends on the material and the screw
type. On your drill there are 20 selectable settings. A slipping clutch stops
the drill chuck from turning when the set torque is reached.
Set the desired torque with setting ring (2):
• Level 1: minimum torque (for small screws and sensitive materials)
• Level 20: maximum torque (for large screws and robust materials)
• Drill symbol: Torque setting switched off.
EN
6

7. CARE AND MAINTENANCE

8. TECHNICAL DATA

Selecting the rotation direction
• Do not set the left/right rotation switch (3) during drilling.
• The rotation direction is always according to the switch position.
• Switch position R: right-rotation/forward/clockwise.To drill and to screw in
screws, push the right/left rotation switch (3) all the way to the right.
• Switch position L: left-rotation/backward/counter-clockwise. To loosen or pull out
screws and nuts, push the right/left rotation switch (3) to the left until the stopper.
Cooling the motor
If the motor has intensely overheated, allow it to run idle for 2 to 3 minutes on
maximum rotation speed.
CARE AND MAINTENANCE
Danger of injury!
Before all care and maintenance work:
• Turn the machine off.
• Wait until the machine has come to a complete standstill.
• Pull out the power plug.
Cleaning
Clean the machine regularly after each use from dust, shaving, wood splinters,
etc. Clean the machine with a moist cloth and some soft soap. Do not use any
detergents or solution; these may cause corrosion of the plastic parts of the
machine. Make sure that no water reaches the inside of the machine.
Servicing
There are no parts on the inside of the machine which require maintenance by
the user. Should the machine fail to function after a long operation time, have it
checked by a technician.
Replacement parts
Danger of accident!
• Parts which were not reviewed and approved by the manufacturer can damage
the machine and can cause serious injuries.
• Use only original parts for replacing old parts, particularly for safety
mechanisms and cutting tools.
TECHNICAL DATA
Operating power
Capacity
Idle rotation speed SD300 / SD300/2
Torque SD300 / SD300/2
Chuck capacity
Maximum drilling diameter wood/steel
Maximum bit diamemer
Weight SD300 / SD300/2
230V ~50 Hz
280 W
0-800 RPM / 0-370/0-1050 RPM
14Nm / 10Nm/17Nm
10 mm
25 mm/10 mm
6 mm
1.15 kg/1,2 kg
EN
7