Safety Advice; Personal Safety; Parts And Accessories; Prior To First Use - Status SD300 Originalbetriebsanleitung

2. SAFETY ADVICE

3) PERSONAL SAFETY

• Stay alert, watch what you are doing and use common sense when operating
a power tool. Do not use a power tool while you are tired or under the influence
of drugs, alcohol or medication. A moment of inattention while operating power
tools may result in serious personal injury.
• Use safety equipment. Always wear eye protection. Safety equipment such as
dust mask, non-skid safety shoes, hard hat, or hearing protection used for
appropriate conditions will reduce personal injuries.
• Avoid accidental starting. Ensure the switch is in the off position before
plugging in. Carrying power tools with your finger on the switch or plugging in
power tools that have the switch on invites accidents.
• Remove any adjusting key or wrench before turning the power tool on.
A wrench or a key left attached to a rotating part of the power tool may result
in personal injury.
• Do not overreach. Keep proper footing and balance at all times.
This enables better control of the power tool in unexpected situations.
• Dress properly. Do not wear loose clothing or jewellery. Keep your hair,
clothing and gloves away from moving parts. Loose clothes, jewellery or long
hair can be caught in moving parts.
• If devices are provided for the connection of dust extraction and collection
facilities, ensure these are connected and properly used. Use of these devices
can reduce dust related hazards.
4) POWER TOOL USE AND CARE
• Do not force the power tool. Use the correct power tool for your application.
The correct power tool will do the job better and safer at the rate for which it
was designed.
• Do not use the power tool if the switch does not turn it on and off. Any power
tool that cannot be controlled with the switch is dangerous and must be
repaired.
• Disconnect the plug from the power source before making any adjustments,
changing accessories, or storing power tools. Such preventive safety measures
reduce the risk of starting the power tool accidentally.
• Store idle power tools out of the reach of children and do not allow persons
unfamiliar with the power tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained users.
• Maintain power tools. Check for misalignment or binding of moving parts,
breakage of parts and any other condition that may affect the power tools
operation. If damaged, have the power tool repaired before use. Many
accidents are caused by poorly maintained power tools.
• Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp
cutting edges are less likely to bind and easier to control.
EN
4

3. PARTS AND ACCESSORIES

4. PRIOR TO FIRST USE

• Use the power tool, accessories and tool bits etc., in accordance with these
instructions and in the manner intended for the particular type of power tool,
taking into account the working conditions and the work to be performed.
Use of the power tool for operations different from intended could result in a
hazardous situation.
5) SERVICE
• Have your power tool serviced by a qualified repair person using only identical
replacement parts. This will ensure that the safety of the power tool is
maintained.
Additional safety instructions for your electric drill
• Do not use the electric power tool with a damaged cable. Do not move the
damaged cable, and pull out the power plug if the cable becomes damaged
during operation. Damaged cables increase the risk of electric shock.
• If the replacement of the supply cord is necessary, this has to be done by the
manufacturer or his agent in order to avoid a safety hazard.
• Materials containing asbestos may not be worked on. Fine dust particles can
remain in the air, despite the installation of a dust vacuum, and can greatly
endanger your health.
PARTS AND ACCESSORIES
1. Chuck (with 10 mm tooth ring)
2. Torque adjustment ring
3. Left/right rotation switch
4. On/off button
5. 2-speed function switch (SD300/2)
PRIOR TO FIRST USE
Danger of injury!
Before all adjustments and settings:
• Turn the machine off.
• Wait until the machine has come to a complete standstill.
• Pull out the power plug.
Inserting the drill
• Place the drill socket key in one of the side holes of the drill socket and turn the
drill socket clockwise.
• Select a designated drill and push it as far as possible into the drill socket
opening.
• Tighten the drill socket by turning it counter-clockwise. Make sure that the drill
is secure in the drill socket.
• Conduct a short test-run and make sure that the drill is tightly secured even
after a complete run.
Using screw tools
When using screw bits, you should always use a universal bit holder.
EN
5