Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Changing the sanding sheet (see figure C)
Remove dirt and dust from the sanding plate (7), e.g. with a
brush, before attaching a new sanding sheet.
To ensure optimum dust extraction, make sure that the
punched holes in the sanding sheet are aligned with the
drilled holes in the sanding plate.
The sanding plate (7) is fitted with a hook-and-loop fasten-
ing, allowing sanding sheets with a similar backing to be se-
cured quickly and easily.
Tap the hook-and-loop fastening of the sanding plate (7) be-
fore fitting the sanding sheet (8) to facilitate maximum adhe-
sion.
The power tool is equipped with two sanding sheets. De-
pending on their state of wear, these can also be changed in-
dividually.
Only use the power tool when both sanding sheets are
u
fitted.
Only use sanding sheets with the same grit.
u
Position the sanding sheet (8) so that it is flush with one a
side of the sanding plate (7), then place the sanding sheet
on the sanding plate and press it on firmly.
To remove the sanding sheet (8), take hold of it by an edge
and pull it away from the sanding plate (7).
Sanding accessories such as fleece/polishing felt are at-
tached to the sanding plate in the same way.
Choosing the sanding sheet
Different sanding sheets are available, depending on the ma-
terial you are working with and the required surface removal
rate:
Application
Can be used to work on all materials including
wood, paint, filler, varnish, hard and softwood
as well as chipboard and metal
For pre-sanding, e.g. of rough and un-
even beams and boards
For surface sanding and levelling of
slight irregularities
For finishing and fine sanding of hard
woods
For any finishing work, such as polishing (metal and stone in
particular), use fleece/polishing felt.
Different types of fleece and polishing felts should be used
depending on the surface finish required on the workpiece.
Operation
Starting Operation
Switching On/Off
Make sure that you are able to press the On/Off switch
u
without releasing the handle.
To switch on the power tool, tilt the on/off switch (1) to-
ward the right to the "I" position.
Bosch Power Tools
To switch off the power tool, tilt the on/off switch (1) to-
ward the left to the "O" position.
Temperature-dependent overload protection
In normal conditions of use, the power tool cannot be over-
loaded. If the power tool is overloaded or the permitted bat-
tery temperature is exceeded, the electronics of the power
tool will switch off until the temperature returns to within the
optimum operating temperature range.
Practical advice
Remove the battery from the power tool before carry-
u
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
Always wait until the power tool has come to a com-
u
plete stop before placing it down.
The material removal rate and the sanding finish are primar-
ily determined by the choice of sanding sheet and the con-
tact pressure.
Only immaculate sanding sheets achieve good sanding per-
formance and make the power tool last longer.
Be sure to apply consistent contact pressure in order to in-
crease the lifetime of the sanding sheets.
To sand corners, edges and hard-to-reach areas accurately,
you can also work with the tips alone or with an edge of the
sanding plate.
Excessively increasing the contact pressure will not lead to
increased sanding performance, rather it will cause more
severe wear of the power tool and of the sanding sheet.
Grit
Do not use a sanding sheet for other materials after it has
been used to work on metal.
40–180
Use only original Bosch-sanding accessories.
Maintenance and Service
Coarse 40
Maintenance and Cleaning
Medium 80, 120
Remove the battery from the power tool before carry-
u
ing out work on the power tool (e.g. maintenance,
Fine
180
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
To ensure safe and efficient operation, always keep
u
the power tool and the ventilation slots clean.
After-Sales Service and Application Service
Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. You can find explosion drawings and information on
spare parts at: www.bosch-pt.com
The Bosch product use advice team will be happy to help you
with any questions about our products and their accessor-
ies.
English | 15
1 609 92A 88G | (12.08.2022)
Werbung
Inhaltsverzeichnis
