Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
10.3
General safety instructions
To avoid malfunctions, damage and health impairments when working with the product, the following
points must be observed in addition to the general rules for safe working:
•
Check the product for completeness and function before commissioning. Only use the prod-
uct if the separating protective devices required for machining and other non-separating pro-
tective devices are fitted.
Make sure that the guards are in good working order and properly maintained.
•
Provide adequate space around the product.
•
Ensure sufficient lighting conditions at the workplace to avoid stroboscopic effects.
•
•
Ensure a clean working environment.
•
Keep the area around the product free of obstacles.
Check the product's connections for strength before each use.
•
Never leave the running product unattended. Switch off the product before leaving the work-
•
ing area and secure it against unintentional or unauthorized restarting.
•
The product may only be operated, maintained or repaired by persons who are familiar with it
and have been informed about the dangers arising in the course of such work.
•
Ensure that unauthorized persons are only at an appropriate safety distance from the product
and keep children in particular away from the machine.
•
Always work carefully and with due caution and never use excessive force.
•
Do not overload the product!
•
Refrain from working on the product when tired, unfocused or under the influence of medica-
tion, alcohol or drugs!
•
Do not use the product in areas where fumes from paints, solvents or flammable liquids are a
potential hazard (risk of fire or explosion!).
•
Warning signs and/or stickers on the product that are illegible or have been removed must be
replaced immediately!
10.4
Special safety instructions for this product
DO NOT use unsuitable power cords.
•
DO NOT place the product near a fire or expose it to heat. Keep it away from direct sunlight.
•
DO NOT charge, use or store the product in a bathroom or any place exposed to rain or mois-
•
ture.
Do not drop the product into water. If the battery of the product comes into contact with wa-
•
ter, this may cause chemical degradation of the battery. This may cause the battery to catch
fire or explode.
Never use or charge swollen, leaking or damaged batteries. If your battery is abnormal, contact
•
us for assistance.
•
Never insert or remove a battery from the product when it is on.
DO NOT use the batteries in strong electrostatic or electromagnetic environment. Otherwise,
•
battery control board may malfunction, resulting in serious accidents.
•
Do not disassemble or pierce the product. Otherwise, it may leak, catch fire or explode.
•
DO NOT use the product if it has been involved in an accident or has suffered a severe impact.
If the product falls into water during use, remove it immediately and place it in a safe and open
•
place. Keep a safe distance until it is completely dry. Never use it again and dispose of it
properly as described in the "Disposal" section below. If the product catches fire, it is recom-
mended that fire extinguishing agents be used in the following order: Water or water mist,
sand, fire blanket, dry powder, carbon dioxide fire extinguisher.
Be careful not to insert pins, wires or other metal parts into the unit housing, outputs or con-
•
trols. Metal parts can short-circuit the unit.
Avoid collisions. DO NOT place heavy objects on the product.
•
Use and store the product only in a clean and dry environment. Do not use or store the product
•
in a dusty or humid environment.
If there is dirt on a plug or socket, clean it with a dry cloth. Otherwise, abrasion may occur,
•
resulting in power loss or inability to charge the product.
•
DO NOT place the product in a microwave oven or in a pressurized container.
To avoid short-circuiting, keep the product away from all metal objects (e.g. coins, hairpins,
•
keys, etc.).
•
Do not heat the product or dispose of it in fire, water or other liquids. Keep the product away
from high temperatures. Do not expose the product to direct sunlight.
ZIPPER MASCHINEN GmbH
www.zipper-maschinen.at
SAFETY
18
ZI-PS330 & ZI-PS1000
Werbung
Inhaltsverzeichnis
Fehlerbehebung
