Battery Charger - WARRIOR WEP8181CS Bedienungsanleitung

OPERATION
Cutting edges on chain are sharp. Use protective
gloves when handling chain.
Keep chain sharp. Your saw will cut faster and more
safely. A dull chain will cause undue sprocket, guide bar,
chain, and motor wear. If you must force chain into wood
and cutting creates only sawdust with few large chips,
chain is dull.
Please contact customer service agent or approved
service agent for sharpening.

BATTERY CHARGER

SPECIFICATIONS
Charger: C8360/C8362
Input: 120-240VAC, 50/60Hz, Max.3A
Output: 63VDC. Max.4.5A
Weight: 2.6 lbs (1.2kg)
WARNING
The battery is not shipped/transported fully
charged. Fully charge the battery before first use
to ensure that maximum run time can be achieved.
This lithium-ion battery will not develop a memory
and may be charged at any time.
CHARGING PROCEDURE
Charging Fully Charged Battery Hot Charging Fault
LED STATUS DESCRIPTION
Blinking Green Charging
Solid Green Fully charged
Solid Red Stand by
Blinking Red (fast) Charging fault
Blinking Red (slow) Battery too hot
Low voltage charging:
If the battery has been stored with little to no charge for
a long period of time, the charger will go into recovery
mode, which will take more time to fully charge the
battery. This will enhance the life of the battery. Once it
is fully charged, the next charge will return to standard
charging.
A fully discharged battery pack will require the allotted
time as stated in the battery manual. Plug the charger
into an AC power outlet.
Insert the battery -into the charger.
This is a diagnostic charger. The Charger LED Lights will
illuminate in specific order to communicate the current
battery status. They are as follows·:
False defect note:
When the battery is inserted into the charger and the
status LED blinks RED, remove the battery from the
charger for 1 minute, then reinsert. If the status LED
blinks GREEN, then the battery is properly charging. If
the status LED is still blinking RED, remove the battery
and unplug the charger for 1 minute. After 1 minute,
plug in the charger and reinsert the battery. If the status
LED blinks GREEN, then the battery is properly charging.
If the status LED is still blinking RED, the battery is
defective and needs to be replaced
CHECKING THE CHARGE
If the battery pack does not charge properly:
Check the current at the power outlet with another tool.
Make sure that the outlet is not turned off.
Check that the charger contacts have not been shorted
by debris or foreign material.
If the air temperature is above 104°F or below
45°F, move the charger and battery pack to a room
temperature location and allow to warm up slowly.
14
WARNING
If the battery is inserted into the charger when
warm or hot, the CHARGING LED indicator light
on the charger may switch on and illuminate RED.
If this occurs allow the battery to cool inside of
the charger for up to 30 minutes. Charging should
automatically start once battery has cooled
CHARGER MOUNTING
1. This charger can be installed hanging on a wall
using two #8 screws (not included).
2. Locate the placement for the charger to be wall
mounted.
3. If fastening to wood studs use 2 wood screws (not
included).
4. Drill two holes on center 5.5 in. apart ensuring that
they are vertically aligned.
5. If fastening to drywall use wall anchors (not
included) and screws to secure the charger to the
wall.
Note: If the battery and the charger won't be used for a
long time, remove the battery from the charger and pull
out the AC power plug
MAINTENANCE
WARNING
If the battery is inserted into the charger when
warm or hot, the CHARGING LED indicator light
on the charger may switch on and illuminate RED.
If this occurs allow the battery to cool inside of
the charger for up to 30 minutes. Charging should
automatically start once battery has cooled
Cleaning
Remove the battery pack.
– Brush or blow dust arid debris out of the air vents
using compressed air or a vacuum. Keep the air
vents free of obstructions, sawdust, and wood
chips. Do not spray, wash, or immerse the air vents
in water.
– Wipe off the housing and the plastic components
using a moist. soft cloth. Do not use strong solvents
or detergents on the plastic housing or plastic
bATTERy CHARGER
components. Certain household cleaners may cause
damage, and may cause a shock hazard.
Battery Pack
– Store the battery pack fully charged
– Once the light on the charger turns solid green,
remove the battery from the charger and disconnect
the charger from the outlet.
– Do not store the battery pack on the tool.
– After charging, the battery pack may be stored in
the charger, as long as the charger is not plugged
in.
Charger Maintenance
Keep the charger clean and clear of debris. Do not allow
foreign material to get into the recessed cavity or onto
the contacts. Wipe the charger clean with a dry, soft
cloth. Do not use solvents or water, and do not place the
charger in wet conditions.
Unplug the charger when there is no battery pack in it.
Fully charge the batteries before placing them in
storage.
Store the charger at normal room temperature. Do not
store it in excessive heat. Do not use the charger in
direct sunlight. Recharge at room temperature between
45' F and 104' F (7'C and 40' C). If the battery pack
is hot, allow it to cool down inside of the charger. The
battery will begin charging once it has returned to room
temperature.
15
EN