Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
SAfETy INSTRUCTION
SAfETy INSTRUCTION
WARNING
Always remove the battery from your machine
for transporting, assemble or disassemble parts,
making adjustments and sharpening, cleaning or
when you do not use your tool. This will reduce the
risk of unintentional starting of the machine which
can cause serious injury.
–
Do recharge the battery of your machine with the
charger specified by the manufacturer. A charger
that is suitable for a certain type of battery can
cause a fire when used with another type.
–
The battery should not be crushed. If crushed, it
should not be heated or incinerated, Do not get it
short-circuited or disassembled, or immersed in
any liquid.
–
Only a specific type of battery can be used with a
cordless machine. Use of any other battery may
cause a fire.
–
When the battery is not in use, keep it away from
metal objects such as paper clips, coins, keys,
screws, nails or other objects that connect the
contacts between them. The short-circuit may
cause fire and / or explosion of it, and cause severe
burns and injury.
–
Avoid contact with fluid from a leaking battery
because of overheating or other factors. If this
happens, flush the affected area of the body with
water, and in case your eyes are affected, seek
medical attention immediately.
–
Due to the heat generated during charging, the
charger should not be used on a combustible
surface or in a flammable environment.
–
Never block the air slots of the charger.
–
Never disassemble the machine by yourself. An
incorrect reassembly can cause a risk of electric
shock or fire.
–
Unplug the charger when the machine is not in use
or when you are cleaning the machine.
–
Use only approved extension cords and in perfect
condition.
–
Make sure the ventilation of the place is enough
when charging. Poor ventilation of the charging
can cause a temperature of excessive use, causing
malfunction of the charger. The higher 40 ° C
should be avoided.
–
The charger cannot be put in closed cabinets or
near heat sources such as radiators or sunlight
because it will undergo increased heat which may
cause a fire or damage
–
the charger.
–
If you do not use the battery for a long time, remove
it from the charger and unplug it.
–
Do not attach anything on the charger with rivets or
screws. Rivets or screws may make ineffective on
the insulating housing. An adhesive label is better,
without blocking the ventilation slots.
–
Charge only original batteries.
–
If the power cord is damaged, make it replaced by
an authorized service center to
–
avoid risk of accidents.
WARNING
To avoid the risk of damage and injury, make sure
the operating voltage of the charger, and never
attempt to recharge non-rechargeable batteries.
10
ASSEMbLy
WARNING
Do not connect the chain saw to mains before it is
completely assembled. Always use gloves when
handling the chain.
CHAIN AND CHAIN BAR ASSEMBLY
The chain MUST be so fitted over the guide bar that the
cutting edges of the cutters (a) face in the direction that
the chain runs (Usually forward)
Hold the guide bar with the nose upwards and place
the saw chain so on sprocket of the guide bar engage
into the chain links and the bottom sections of the drive
links are situated in the groove of the bar. The chain is
correctly tensioned when it is still possible to raise it by
3-4 mm. The direction of rotation of the saw chain is
indicated by two arrows on the drive-sprocket cover.
- Unpack all parts carefully.
- Place the chain saw on any suitable flat surface with
the motor facing downwards.
Fit the chain onto the drive sprocket and guide the chain
bar. So that the fastening bolt and the two guide fins lit
into the keyway of the chain bar. Check if all parts are
seated properly and hold chain and chain bar in a level
position.
- Fit cover. Check that arrows are still aligned
- Hand lighten locking knob on fastening bolt.
- Proceed to "tensioning chain".
ASSEMbLy
Battery pack assembly
Put the battery as shown above, taking care to press any
button to prevent accidental starting.
Lubrication
CAUTION
The chain saw is not supplied filled with oil. It is
essential to fill the chain oil before use. Never
operate the chain saw without chain oil or at an
empty oil tank level, as this will result in over
heating or extensive damage to the product.
Chain life and cutting capacity depend on optimum
lubrication. Therefore, the chain is automatically
oiled during operation via oil outlet.
Filling oil tank:
1.
Set chain saw on any suitable surface with oil filler
cap facing upward.
2. Clean area around the oil filler cap with cloth
unscrew cap.
3. Do not remove filter insert during filling.
4. Add chain saw oil until reservoir is full.
5. Avoid dirt or debris entering oil tank, refit oil filler
cap and tighten
11
EN
Werbung
Inhaltsverzeichnis
