Maintenance And Service; Maintenance And Cleaning - Bosch GGS Professional 8 CE Originalbetriebsanleitung

OBJ_BUCH-1269-005.book Page 15 Wednesday, June 18, 2014 2:52 PM
Dust/Chip Extraction
 Dusts from materials such as lead-containing coatings,
some wood types, minerals and metal can be harmful to
one's health. Touching or breathing-in the dusts can cause
allergic reactions and/or lead to respiratory infections of
the user or bystanders.
Certain dusts, such as oak or beech dust, are considered
as carcinogenic, especially in connection with wood-treat-
ment additives (chromate, wood preservative). Materials
containing asbestos may only be worked by specialists.
– Provide for good ventilation of the working place.
– It is recommended to wear a P2 filter-class respirator.
Observe the relevant regulations in your country for the mate-
rials to be worked.
 Prevent dust accumulation at the workplace. Dusts can
easily ignite.
Operation
Starting Operation
 Observe correct mains voltage! The voltage of the pow-
er source must agree with the voltage specified on the
nameplate of the machine. Power tools marked with
230 V can also be operated with 220 V.
Switching On and Off
To start the power tool, push the On/Off switch 5 forwards.
To lock the On/Off switch 5, press the On/Off switch 5 down
at the front until it latches.
To switch off the power tool, release the On/Off switch 5 or,
if it is locked, briefly push down the back of the On/Off switch
5 and then release it.
To save energy, only switch the power tool on when using it.
Kickback stop
In case of a sudden drop in speed, e.g., caused by a jammed
disc while cutting, the power supply to the motor is electroni-
cally interrupted.
To restart the operation, switch the On/Off switch 5 to the
Off position and start the machine again.
Constant Electronic Control
Constant electronic control holds the speed constant at no-
load and under load, and ensures uniform working perfor-
mance.
Speed preselection (GGS 8 CE/GGS 28 CE/GGS 28 LCE)
The required speed can be preselected with the thumbwheel
6 (also while running).
The required speed depends on the material being worked
and the diameter of the application tool. Observe the maximal
allowable speed of the application tool.
Bosch Power Tools
Thumbwheel No-load speed (min
Position
GGS 28 CE
GGS 28 LCE
1 10000
2 12700
3 16700
4 19700
5 23500
6 28000
Working Advice
Optimum grinding results are achieved when the grinding tool
is moved uniformly back and forth with light pressure. Pres-
sure that is too strong reduces the performance capability of
the machine and causes the grinding tool to wear more quick-
ly.
 Protect the abrasive wheels from impacts.

Maintenance and Service

Maintenance and Cleaning

 Before any work on the machine itself, pull the mains
plug.
 For safe and proper working, always keep the machine
and ventilation slots clean.
 In extreme conditions, always use dust extraction as
far as possible. Blow out ventilation slots frequently
and install a residual current device (RCD). When work-
ing metals, conductive dust can settle in the interior of the
power tool. The total insulation of the power tool can be im-
paired.
Please store and handle the accessory(-ies) carefully.
If the replacement of the supply cord is necessary, this has to
be done by Bosch or an authorized Bosch service agent in or-
der to avoid a safety hazard.
After-sales Service and Application Service
Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. Exploded views and information on spare parts can al-
so be found under:
www.bosch-pt.com
Bosch's application service team will gladly answer questions
concerning our products and their accessories.
In all correspondence and spare parts order, please always in-
clude the 10-digit article number given on the type plate of
the machine.
English | 15
-1
)
GGS 8 CE
2500
3600
4600
5700
6800
8000
3 609 929 C85 | (18.6.14)