Operation; Maintenance - Makita GD0600 Betriebsanleitung

ASSEMBLY
CAUTION:
• Always be sure that the tool is switched off and
unplugged before carrying out any work on the tool.
Installing or removing wheel point
Loosen the collet nut and insert the wheel point into the
collet nut. Use one wrench to hold the spindle and the
other one to tighten the collet nut securely. (Fig. 2)
The wheel point should not be mounted more than 8 mm
from the collet nut. Exceeding this distance could cause
vibration or a broken shaft. (Fig. 3)
To remove the wheel point, follow the installation
procedure in reverse.
CAUTION:
• Use the correct size collet cone for the wheel point
which you intend to use.

OPERATION

Turn the tool on without the wheel point making any
contact with the workpiece and wait until the wheel point
attains full speed. Then apply the wheel point to the
workpiece gently. To obtain a good finish, move the tool in
the leftward direction slowly. (Fig. 4)
CAUTION:
• Apply light pressure on the tool. Excessive pressure on
the tool will only cause a poor finish and overloading of
the motor.

MAINTENANCE

CAUTION:
• Always be sure that the tool is switched off and
unplugged before attempting to perform inspection or
maintenance.
To maintain product SAFETY and RELIABILITY, repairs,
carbon brush inspection and replacement, any other
maintenance or adjustment should be performed by
Makita Authorized Service Centers, always using Makita
replacement parts.
ACCESSORIES
CAUTION:
• These accessories or attachments are recommended
for use with your Makita tool specified in this manual.
The use of any other accessories or attachments might
present a risk of injury to persons. Only use accessory
or attachment for its stated purpose.
If you need any assistance for more details regarding
these accessories, ask your local Makita Service Center.
Side handle (Fig. 5)
When using the side handle, remove the rubber protector,
insert the side handle on the tool barrel as far as it will go
and rotate it to the desired angle. Then tighten the handle
firmly by turning clockwise.
CAUTION:
• When using the tool without handle, always install the
rubber protector on the tool.
• When installing the rubber protector, always push it
onto the tool until the protrusion inside the rubber fits to
the grooves in the tool.
• Wheel points
• Collet cone set (3 mm, 6 mm, 1/4", 1/8")
• Vise holder
• Wrench 13
• Side handle set
For European countries only
Noise
The typical A-weighted noise level determined according
to EN60745:
Sound pressure level (L
Uncertainty (K): 3 dB (A)
The noise level under working may exceed 80 dB (A).
Wear ear protection.
Vibration
The vibration total value (tri-axial vector sum) determined
according to EN60745:
Work mode: surface grinding
Vibration emission (a
Uncertainty (K): 1.5 m/s
EC Declaration of Conformity
We Makita Corporation as the responsible
manufacturer declare that the following Makita
machine(s):
Designation of Machine: Die Grinder
Model No./ Type: GD0600
are of series production and
Conforms to the following European Directives:
98/37/EC until December 28th 2009 and then with
2006/42/EC from 29th December 2009
And are manufactured in accordance with the following
standards or standardised documents:
EN60745
The technical documentation is kept by our authorised
representative in Europe who is:
Makita International Europe Ltd.,
Michigan, Drive, Tongwell,
Milton Keynes, MK15 8JD, England
30th January 2009
Tomoyasu Kato
Makita Corporation
3-11-8, Sumiyoshi-cho,
Anjo, Aichi, JAPAN
): 74 dB (A)
pA
2
): 2.5 m/s or less
h,SG
2
ENH101-12
Director
ENG104-1
ENG206-3
5