Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
To actuate the fuel gauge, press and hold the fuel gauge
button
21
. A combination of the three green LED lights will
illuminate designating the level of charge left. When the level
of charge in the battery is below the usable limit, the fuel gauge
will not illuminate and the battery will need to be recharged.
nOTE: The fuel gauge is only an indication of the charge left on
the battery pack. It does not indicate tool functionality and is
subject to variation based on product components, temperature
and end‑user application.
Installing and Removing the Bit (Fig. A)
This tool is designed for spiral cutting bits with either a 3 mm
(1/8"), 4 mm (5/32") (4 mm collet sold separately), or 6 mm
(1/4") shank and has a tool‑free bit change system. To change
bits, FIRST turn off the tool and disconnect the battery from the
tool. Remove the cutting depth guide
1. To replace bit, depress both spindle lock button
collet lock
and turn collet grip
5
2. Insert or remove bit.
WARNING: The bits are sharp and should be handled
with great care.
CAUTION: When replacing bits, do not insert cutting
flutes into the collet. This may result in broken bits.
3. While depressing both spindle and collet locks, turn the
collet grip clockwise to firmly tighten the collet. For some
heavy duty applications, it may be necessary to use a
wrench to further tighten the collet nut
the spindle lock button
4. Reattach the cutting depth guide.
CAUTION: Never tighten the collet without a bit installed.
This tool comes with both 3 mm (1/8") and 6 mm (1/4")
collets. To change collets, remove the collet nut and insert the
desired collet. Always use a collet with a matching diameter to
that of the bit being installed.
Depth Guide (Fig. A)
Cutting depth guide
snaps onto locators as shown. Keep
2
depth guide in place at all times during operation of the tool.
For best results, adjust the cutting depth guide using the knob
to allow the bit to protrude about 6.35 mm past the thickness of
material to be cut. Ensure that when cutting, the entire material
thickness will engage with the bit's flutes.
Attaching the Dust Shroud (Fig. A, F)
The DCE555DC dust shroud is also available for use with this
tool. This accessory connects to the tools cutting depth guide to
function as both a cutting depth guide and a dust shroud. It is
compatible with the DWH161 D
(sold separately).
To attach the dust shroud, FIRST turn off the tool and disconnect
the battery from the tool.
1. Remove the cutting depth guide
2. Fully unscrew the knob and separate the knob
washer
17
from the cutting depth guide
2
.
7
counterclockwise.
6
while depressing
4
.
7
WALT Universal Dust Extractor
e
2
.
16
2
.
3. Replace the front portion of the cutting depth guide with
the dust shroud
4. Rethread the washer and the knob and tighten into the base
of the cutting depth guide.
5. Snap dust shroud/cutting depth guide onto the tool.
Attaching a Dust Extractor to the Dust Shroud
(Fig. G)
The DCE555DC dust shroud is compatible with the DWH161
DEWALT Universal Dust Extractor (sold separately).
•
Friction‑fit the the dust shroud
the DWH161 Universal Dust Extractor.
Belt Clip (Fig. C)
WARNING: To reduce the risk of serious personal injury,
ensure the screw holding the belt clip is secure.
and
IMPORTanT: When attaching or replacing the belt clip
use only the screw
tighten screw.
If the belt clip is not desired at all, it can be removed from
the tool.
To remove the belt clip, remove the screw
clip in place.
OPERATION
Instructions for Use
WARNING: Always observe the safety instructions and
applicable regulations.
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.
Proper Hand Position (Fig. D)
WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.
WARNING: To reduce the risk of serious personal injury,
ALWAYS hold securely in anticipation of a sudden reaction.
WARNING: Tool may stall (if overloaded or improperly
used) causing a twist. Always expect the stall. Grip the tool
firmly with both hands to control the twisting action and
prevent loss of control which could cause personal injury.
Proper hand position requires one hand on the handle
the other bracing the battery to control the twisting action of
the tool.
On/off Button (Fig. A)
•
To start the motor, press the on/off button
•
To stop the motor, press the on/off button
and the
14
.
port to the hose
14
that is provided. Be sure to securely
12
12
EnGLIsh
of
18
11
,
that holds the belt
15
and
1
.
again.
1
35
Werbung
Inhaltsverzeichnis
