Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Installation
Do not mount the door/window contact transmitter (C1) and magnet (C2) in the area
of metal or electrical wiring.
The magnet (C2) must be mounted at the same height as the transmitter (C1). For
this purpose, 3 spacers are included, which can also be combined. Please note the
table after installation.
• Glue the door/window contact transmitter (C1) to the edge of
the desired door or window.
Before doing this, degrease the place of attachment of the
transmitter (C1).
Align the transmitter (C1) so that the side with the notched
triangle faces outwards (on the side where the magnet (C2)
will later be located). Please refer to the picture.
• Now glue the magnet (C2) to the frame of the door or window
where you have previ-ously attached the transmitter (C1). It
should be attached as far inside as possible.
With the door/window closed, the distance between the magnet (C2) and the trans-
mitter (C1) must not exceed 1 cm.
Before doing this, degrease the gluing spot again.
Spacer
Height in mm
3
5
14.5
8
17.5
19.5
22.5
Gateway configuration and setup
More information about gateway configuration and setup in combination with the
mobile app can be found in the operating instructions for the app.
Care and cleaning
Never use aggressive detergents, rubbing alcohol or other chemical solutions, as
these could damage the housing or even impair the functioning of the product.
• Use a dry, lint-free cloth to clean the product.
Disposal
a) Product
This symbol must appear on any electrical and electronic equipment placed on the
EU market. This symbol indicates that this device should not be disposed of as
unsorted municipal waste at the end of its service life.
Owners of WEEE (Waste from Electrical and Electronic Equipment) shall dispose
of it separately from unsorted municipal waste. Spent batteries and accumulators,
which are not enclosed by the WEEE, as well as lamps that can be removed from
the WEEE in a non-destructive manner, must be removed by end users from the
WEEE in a non-destructive manner before it is handed over to a collection point.
Distributors of electrical and electronic equipment are legally obliged to provide free take-back
of waste. Conrad provides the following return options free of charge (more details on our
website):
• in our Conrad offices
• at the Conrad collection points
• at the collection points of public waste management authorities or the collection points set up
by manufacturers or distributors within the meaning of the ElektroG
End users are responsible for deleting personal data from the WEEE to be disposed of.
It should be noted that different obligations about the return or recycling of WEEE may apply in
countries outside of Germany.
Spacer
A
B
C
A+B
A+C
B+C
A+B+C
b) (Rechargeable) batteries
Remove batteries/rechargeable batteries, if any, and dispose of them separately from the
product. According to the Battery Directive, end users are legally obliged to return all spent
batteries/rechargeable batteries; they must not be disposed of in the normal household waste.
Batteries/rechargeable batteries containing hazardous substances are labelled with
this symbol to indicate that disposal in household waste is forbidden. The abbrevi-
ations for heavy metals in batteries are: Cd = Cadmium, Hg = Mercury, Pb = Lead
(name on (rechargeable) batteries, e.g. below the trash icon on the left).
Used (rechargeable) batteries can be returned to collection points in your municipality, our
stores or wherever (rechargeable) batteries are sold. You thus fulfil your statutory obligations
and contribute to environmental protection.
Batteries/rechargeable batteries that are disposed of should be protected against short circuit
and their exposed terminals should be covered completely with insulating tape before disposal.
Even empty batteries/rechargeable batteries can contain residual energy that may cause them
to swell, burst, catch fire or explode in the event of a short circuit.
Declaration of Conformity (DOC)
Conrad Electronic SE, Klaus-Conrad-Straße 1, D-92240 Hirschau, hereby declares that this
product conforms to Directive 2014/53/EU.
Click on the following link to read the full text of the EU Declaration of Conformity:
www.conrad.com/downloads
Select a language by clicking on the corresponding flag symbol, and then enter
the product order number in the search box. The EU Declaration of Conformity is
available for download in PDF format.
Technical data
Power supply .............................................. 1x CR 2450 button cell
Current consumption .................................. max. 15 mA
Transmission frequency.............................. 868 MHz
Range ......................................................... ≤ 80 m (outdoors)
Frequency range/Transmission power ....... 865.2 ~ 868.4 MHz/+7dBm
Dimensions (W x H x D) ............................. approx. 31 x 56 x 16 mm (transmitter)
Weight ........................................................ approx. 33 g
Operating/storage conditions ...................... 0 °C to +55 °C, ≤ 80% RH (non-condensing)
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com). All rights in-
cluding translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data
processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication
represents the technical status at the time of printing.
Copyright 2022 by Conrad Electronic SE.
approx. 10 x 25 x 9 mm (magnet)
*2269124_v3_0922_02_dm_mh_2L
Werbung
