EM2GO EMB011AC1RW Bedienungsanleitung Seite 9

GB
ATTENTION!
Make absolutely sure that the cover is tightly closed to ensure splash water protection and to
protect the system from moisture penetration.
Mounting the supply cables
RISK OF ELECTRIC SHOCK!
Make sure that the connection cable is not connected to the mains when connecting it to the
charging station! Only qualified personnel are allowed to connect the cable!
Use pre-installed supply cable:
The charging station is equipped with a 60cm
long 5x4mm² NYY-J supply cable.
As shown in Fig.9, connect the supply cable
to an RCD (type A 30mA) equipped and
the fuse must be connected to the distribution
board protected by an automatic circuit
breaker (CB C25).
Connect your own supply cable:
1. Open the cover as described under „Opening the
housing cover" and remove the ribbon cable from
the boards (Fig.10/3).
2. Remove the existing supply cable from the
charging station.
3. Feed the prepared supply cable (Fig.10/1) through the
rubber grommet (Fig.10/2).
4. Remove approx. 12 mm of insulation from the
conductors of the supply cable. Multicore conductors
should be fitted with wire end ferrules in advance to
ensure a secure connection. Connect the conductors
of the supply cable to the screw bar of the charging
station as follows and screw it tight (approx. 4Nm):
L1 Brown | L2 Black | L3 Gray | N Blue | PE Green Yellow.
5. Connect the ribbon cable to the two boards (Fig.10/3).
6. Place the protective cover on the housing and press
until the cover audibly clicks into place. Fix the cover
from below with the screw.
Status LED
The status LED indicates the following states of the charging station:
1. Red-green-blue slow change: LED self-test at power-up
2. Green constantly on: Standby mode
3. Blue constant on: Connected to an EV
4. Blue flashes slowly: charging in progress
5. Purple flashing: Charging process completed
6. Red-yellow flashing alternately: Fault
7. Red-blue flashing alternately: Upgrade
15
Fig.9
3
Fig.10
2
1
Charge vehicle
Note:
The vehicle to be charged must be parked, switched off and the parking brake applied.
Charging station
Charging port
Type 2 plug
Cable
1. Remove the type 2 plug from the charging plug holder and connect it to the vehicle's
charging port. Please note that the vehicle is prepared and set for charging.
2. Key mode: Press the charge control key after inserting the plug, the charging process
starts. Press the key again to stop the charging process.
RFID mode: You can control the charging process by holding the RFID card after
inserting the charging port. The charging process starts when a pre-configured RFID card
touches the designated area for RFID application. Likewise, the charging process can be
stopped by touching the area with the RFID card.
3. After charging is complete, remove the Type 2 plug from the vehicle's charging port.
If you are unable to pull out the plug, press the unlock button on the vehicle or key.
NOTICE:
The table of error codes can be found on page 18.
RFID cards
The charging station is supplied with two RFID cards that can be used to start and stop charging
processes.
Programming RFID cards
Proceed as follows to program additional RFID cards:
1. Switch on the charging station and disconnect the cable from the vehicle.
2. Press and hold the charge control button until the LED changes from green to blue.
3. Hold new RFID card (offline mode) to RFID reader for at least 10 seconds. The LED flashes and six
acoustic signals sound. The RFID card is now ready for use.
4. To exit the mode, press and hold the charge control button until the LED changes from blue to
green.
Communication
The charging station has a wireless interface to Bluetooth enabled devices for communication in
conjunction with the EM2GO App „EM2APP". The app is connected to the charger via Bluetooth for
data interaction. It allows you to control the charging process and set the charging method. You can
follow the status of the charger and the real time data of the charging process and have the possibility
to view records, statistics of charging jobs, etc.
Install app
1. Activate the Bluetooth function on your smartphone or tablet.
2. Download and install the app „EM2APP" by scanning the QR code.
3. Open the app and register. Click on the QR code icon of the app and scan
the QR code on the charging station. The charging station is now connected
to the Smart device connected and can be controlled via it.
GB
16